A sterilizer that has just come back from a major repair cannot go straight back into patient care because the technician signed the work order. The baseline most Canadian reprocessing teams apply before the unit is released is three consecutive biological indicator (BI) runs, each inside a process challenge device (PCD), on an empty chamber, all three negative — plus a Bowie-Dick test on pre-vacuum units, and a chemical indicator in every run. If any of those three is positive, the count restarts from one after the fault is corrected.
That is the short answer facilities ask for most often. This guide sets out the full sequence, what to record, and how the 3-hour and 24-hour indicator formats change the timeline. If you are setting up the monitoring line on the bench, the DLAB HB105-S1 dry bath incubator is a dry-block unit built for clinics that run one or two sterilizers and need a fixed 37 °C block rather than a shared water bath.
How many biological indicators are required after a major repair?
Three, run consecutively, all negative. The logic is not arbitrary: a single passing BI proves the sterilizer worked for that one cycle, while three consecutive passes demonstrate the repair is stable across the repeat cycles a normal day will produce. A unit that passes once and fails on the second run is far more dangerous than one that fails immediately, because staff start trusting the load release again.
The runs must be done on an empty chamber with the PCD placed in the position that is hardest to sterilize — usually the front-bottom, or the location the sterilizer instruction manual specifies. Load the chamber and you are testing the load, not the sterilizer. Each run also carries a chemical indicator so that you can see at a glance whether the cycle reached temperature, pressure and time at all.
Pre-vacuum (Class B) units add a Bowie-Dick test, because a repaired vacuum pump or door seal can fail to remove air from a dense pack even when the chamber reaches temperature. Gravity displacement units do not need a Bowie-Dick test — air removal is not part of their cycle design.
| Repair category | Typical monitoring before return to service | Record against the work order |
|---|---|---|
| Major: chamber weld, door assembly, vacuum pump, control board, complete overhaul | 3 consecutive BI in PCD, empty chamber; Bowie-Dick per pre-vacuum cycle type; CI in each run; physical parameters verified | BI lot number and expiry, incubator block, cycle number, operator, date, result of each run, work order number |
| Minor: door gasket or filter change, small fitting replaced | Monitoring that matches the sterilizer manufacturer's instructions — commonly a BI in PCD plus a Bowie-Dick on pre-vacuum units | Same fields, one line per run |
| Relocation or reinstallation | Treated as new installation: full validation, then 3 consecutive BI runs before routine release | Validation report filed with the equipment record |
| Routine preventive maintenance | Normal daily monitoring continues; no extra runs unless the manufacturer says otherwise | Daily log |
Two practical notes. First, the sterilizer instruction manual outranks habit — some manufacturers specify a different number of cycles after a vacuum system repair, and provincial expectations can differ between dental, laboratory and hospital settings. Second, the three runs are a release condition, not a formality: no instrument load runs between them, and the unit is tagged out of service until the third negative result is read.
Where must the biological indicator be placed inside the sterilizer?
Inside a process challenge device (PCD), placed in the position that is hardest to sterilize rather than the one easiest to reach. On a gravity-displacement unit that normally means the lower shelf at the front of the chamber, close to the drain; on a pre-vacuum unit the same low front position applies. A bare indicator left on a middle shelf in an empty chamber is too easy to sterilize and can pass on a cycle that would fail a real instrument tray, which is exactly why the validation run uses a PCD. Keep the same position for all three runs, and write it on the validation record next to the result: a result from a documented position can be defended later, an undocumented one cannot.
Which biological indicator format fits the repair timeline?
A 24-hour self-contained BI incubates in the sterilizer's own small incubator and gives a result the next day. For a repair validation on a Monday morning, that means the sterilizer sits idle until Tuesday. A 3-hour fluorescence-readout BI shortens the waiting window to a single working morning, which is why clinics with one sterilizer and a full schedule tend to keep both formats in stock: the rapid format for repair days and busy weeks, the 24-hour format for routine daily monitoring where the cost per test matters more than the turnaround.
Whichever format you use, the three runs after a repair must be the same format with the same lot number, incubated in the same block, so that a positive result cannot be explained away as a mixed-lot artefact. Keep the positive control from the same lot in the same incubation batch — a BI result is only meaningful when the control shows the lot is viable.
What if one of the three biological indicators turns positive?
Stop. Correct the fault, then restart the sequence at one. Do not accept "two out of three" and do not average the result. A positive BI means either the cycle failed to kill the challenge organism or the indicator was mishandled (incubated too late, wrong block temperature, expired lot), and both possibilities have to be closed out in writing before the sterilizer returns to service.
Because no patient load ran during validation, this is a documentation exercise rather than a recall exercise. Record the positive result, the suspected cause, the corrective action and the date the sequence restarted. That single paragraph is what an inspector will look for, and it is far easier to write at the time than to reconstruct six months later.
Does a major repair also require a documentation update?
Yes, and it is the part most often missed. The equipment file for each sterilizer should hold the repair work order, the validation record, the BI lot documentation and the name of the person who released the unit. Where a facility runs a digital log, attach the same documents to the digital record so the paper and the system agree; where the log is a binder, keep the repair record in the same section as the daily monitoring sheets rather than in a separate maintenance folder.
If your facility has ever had a monitoring record go missing, the practical protection is a standing rule: every log page is photographed or exported weekly and stored somewhere the sterilizer cannot destroy. It costs two minutes a week and removes the most common inspection finding in reprocessing.
Where to Buy Repair Validation Indicators in Canada
CliniEco Medical supplies the indicators and incubators used for post-repair validation from Ontario, with CAD pricing published per pack (MDEL #35334) — no quote required, and the lot number on each pack goes straight into the validation record.
| Item | Pack / format | Price (CAD) | Cost per test | Order |
|---|---|---|---|---|
| 24-hour self-contained BI | 25-pack | $69.99 | $2.80 | 24-hour self-contained biological indicator, 25-pack |
| 24-hour self-contained BI | 50-pack | $109.99 | $2.20 | 24-hour self-contained biological indicator, 50-pack |
| 24-hour self-contained BI | 100-pack | $189.00 | $1.89 | 24-hour self-contained biological indicator, 100-pack |
| 1-hour fluorescence rapid BI | 50-pack | $269.99 | $5.40 | 1-hour fluorescence biological indicators, 50-pack |
| 24-hour dry-block incubator | 24 wells | $379.00 | — | CliniEco 24-hour biological indicator incubator, 24-well dry block |
| DLAB HB105-S1 dry-block incubator | 20 wells | $599.00 | — | DLAB HB105-S1 20-well dry-block incubator |
Which sterilizers and formats these fit: repair validation runs on a steam sterilizer use the 24-hour self-contained indicator at 55–60 °C in a dry-block unit, or a fluorescence format read in the 4-well reader when the three consecutive results are needed the same day. All of them are validated for 121 °C gravity-displacement and 132 °C vacuum-assisted (pre-vacuum) cycles; pre-vacuum units also take a Bowie-Dick pack on each validation run. Two sterilizers in one clinic put a day's validation batch in the 24-well unit, while a single sterilizer plus control and repeat wells fits the 20-well unit. Ethylene oxide, dry-heat and hydrogen-peroxide sterilizers need a different indicator biology and sit outside this table — check the cycle type printed on the unit before ordering.
How many packs to hold: sterilizers × test days × cycle types = vials per week. One sterilizer tested on every day it is used, five working days a week, runs 5 vials a week, so the 25-pack covers about five weeks and the 100-pack about four months; two sterilizers on that schedule need 10 vials a week, which makes the 50-pack the five-week size and the 100-pack the ten-week size. Add one vial for every extra cycle type run on the same day, and keep a spare pack for the repeat tests that follow a positive result.
Stock and shipping: every item in the table is held in stock in Toronto and ships from Ontario, with the lot number printed on each indicator pack so the entry in your monitoring log can be traced back to the batch. We do not quote a delivery date at checkout.
Related reading
Frequently Asked Questions
How many biological indicators are required after a major sterilizer repair?
Three consecutive BI runs, each in a PCD on an empty chamber, all negative, before the sterilizer is released. Pre-vacuum units also need a Bowie-Dick test. If any run is positive, correct the fault and restart from one.
Can you run a normal instrument load during repair validation?
No. Validation runs are empty-chamber runs. Instruments are processed only after the third negative result has been read and recorded, and the sterilizer has been formally released back into service.
Does a Bowie-Dick test replace the biological indicator after a repair?
No. A Bowie-Dick test checks air removal in pre-vacuum cycles only. It cannot demonstrate microbial kill, so it supplements the BI runs rather than replacing them.
How long should repair validation records be kept?
Follow your provincial retention rule for sterilization records and keep the repair validation in the same file as the equipment maintenance history. Retention periods differ between dental, laboratory and long-term care settings, so confirm the number that applies to your facility before filing.
Where should the biological indicator go inside the chamber?
In a process challenge device, on the lower front shelf near the drain for both gravity-displacement and pre-vacuum cycles, in the same position for all three validation runs. Note the position on the record.
CliniEco Medical is a licensed medical device establishment (MDEL #35334).
Download the sterilization log sheet generator to record repair validation runs alongside daily monitoring, and work through the provincial sterilization self-check to confirm which tests apply to your sterilizer type. For questions on a specific repair, ask a sterilization compliance specialist.
Sterilization compliance hub · How do you handle a failed biological indicator test? · Sterilizer validation versus routine monitoring in Canada · Biological indicator incubation temperature
Running a clinic, laboratory or care home? Apply for the 24-hour biological indicator 25-pack to trial the monitoring format, or open a wholesale and institutional supply account for case pricing on indicators, PCDs and log sheets. Ordering in volume? The wholesale account covers multi-site purchasing. Reselling? become a distributor.