Tie-On or Ear Loop Masks: Which Retention Suits the Room, and What ASTM F2100 Leaves Out
A hygienist starts a 90-minute hygiene appointment with a mask that fits well at 9 a.m. By 9:40 the loops are pulling her ears forward, and she pushes the mask back up with the back of a gloved wrist. That gesture is the most common mask failure in a dental or medical clinic, and no filtration number on the box prevents it.
Tie-on and ear loop masks pass the same material tests. What separates them is what happens to the mask after it is put on: whether it stays where it was placed, whether the wearer can size it, and how many times a gloved hand has to go near the face in an hour. That is a procurement question about retention, and it is worth more attention than it usually receives because most buying decisions are made on level and price alone.
Our own stock runs to ear-loop formats, because that is what most Canadian rooms specify for turnover. The
Aurelia Level 2 mask is made in Canada with a three-layer construction and a melt-blown middle layer, and it is the format most rooms start with.
What the two formats actually change
| Feature | Tie-on mask | Ear loop mask |
|---|---|---|
| Retention | Knotted at the back of the head; circumference set by the wearer | Elastic loop tension fixed by loop length |
| Donning time | Slower, requires both hands behind the head | Faster, can be done in a doorway |
| Adjustment during wear | Rare; the knot does not move | Frequent; loops stretch and pull the ears forward |
| Fit across head sizes | One carton fits most adults because the tie sets the size | Depends on loop length and ear position |
| Mask-off technique | Untie at the back, lift away from the face | Remove by the loops without touching the front |
| Suits | Long procedures, sessions over an hour, OR-style work | Room turnover, short visits, screening stations |
| Supply format | Usually boxed flat, often 50 per box | Boxed flat, 50 per box, case formats vary |
The table is a trade between speed and stability. There is no format that wins on both, which is why clinics that wear masks for long stretches often stock both.
What ASTM F2100 tests, and what it does not
ASTM F2100 is a materials specification. It sets thresholds for four measured properties: bacterial filtration efficiency (BFE) tested under ASTM F2101, particle filtration efficiency (PFE) under ASTM F2299, differential pressure as a measure of breathability, and resistance to penetration by synthetic blood under ASTM F1862. ISO 22609 covers the same synthetic-blood penetration principle for protective materials, which is why a supplier may quote either test report.
The thresholds are widely published. Level 1 requires BFE and PFE of at least 95 per cent with fluid resistance at 80 mmHg. Level 2 and Level 3 both require at least 98 per cent, with fluid resistance at 120 mmHg for Level 2 and 160 mmHg for Level 3. Differential pressure limits tighten at the higher levels, because a mask that resists more fluid but cannot be breathed through gets pulled down or worn loose.
What the specification does not cover is fit and retention. There is no test in F2100 for "stays in place for ninety minutes", and no test for edge leakage on a specific face. Those are the variables that decide whether a mask is still sitting correctly at the end of a procedure.
Fluid resistance: what 120 and 160 mmHg buy

The synthetic-blood test exists because a splash is a pressure event. A mask rated to 120 mmHg resists a stream of synthetic blood at a defined velocity without visible penetration; 160 mmHg resists a stronger stream. In practice the level maps to the procedure: a Level 2 mask is specified for procedures where a moderate splash is possible, and Level 3 where the fluid volume or pressure is higher.
The number a buyer should hold onto is that fluid resistance is not proportional to how thick the mask feels. It is a property of the barrier layer and the construction at the seams. Two masks can feel identical and sit at different levels, which is why the level has to be on the carton rather than inferred from the look of the product.
For a Canadian clinic, the practical question is which rooms need which level, and whether the same mask can serve both. Many clinics standardise on one level for all clinical rooms and stock a lower level for reception and screening. That simplifies par levels but can under-specify a procedure room or over-specify a waiting area, and both directions carry a cost.
Why the retention question is a routine-practices question
Public Health Ontario's routine practices material treats the mask as part of a set of controls that only work if they are worn correctly and left alone. Hand hygiene guidance is explicit that hands come into contact with the face far less often when the PPE does not need adjusting. A mask that has to be pushed back up every few minutes creates exactly the contact event the guidance is trying to remove.
That is the argument for tie-on masks in long sessions, and it is an argument about behaviour, not filtration. A tied mask is knotted once and stays where it was set. An ear-loop mask with a stretched loop migrates, and the wearer responds.
The counter-argument is equally practical: a tied mask takes longer to put on and longer to take off, which matters at a screening station or in a room where the clinician moves between patients every eight minutes. In those settings the loop is the right answer and the adjustment problem is smaller because the mask is worn for a short time.
Sizing a mixed mask stock
A clinic that stocks both formats needs two par levels, not one. The way to build them is to count what each room actually draws. Log masks issued per room per day for two weeks, separate the procedure rooms from the short-visit rooms, then multiply by working days and add the supplier lead time.
Two habits make that count more accurate. First, record the format on the log, not just the quantity, because a clinic that switches a procedure room from loops to ties will otherwise think usage went up when it only changed shape. Second, count boxes opened rather than boxes on the shelf; the shelf count tells you what you own, not what you use.

What to put on a mask purchase order
Six lines cover the purchasing risk. State the ASTM F2100 level for each room type. State the format (tie-on or ear loop). State the pack format in masks, not boxes, and repeat it in cases. State the fluid resistance figure you are buying at, since two products at the same level can differ in test evidence. State the markings you expect on the carton, using ISO 15223-1 as the reference for symbols. And state the lot coding you want for traceability.
A seventh line is worth adding for multi-site buyers: the quality system the supplier works under. ISO 13485 is the medical device quality management standard, and a supplier holding it has a documented complaint and nonconformance process. ISO 14971 frames how that supplier should think about risk, including the risk that a mask is worn incorrectly because it does not stay in place.
Receiving checks are lower-cost than complaints. ISO 2859-1 gives an attribute sampling scheme: pull a defined number of masks from a defined number of boxes and judge the delivery on defects found. In a clinic that means checking that the nose bridge is present and bendable, that the loops or ties are attached at both points, that the layers are not delaminated at the edge, and that the printed level on the carton matches the purchase order.
What our mask line looks like
Both are ear-loop formats with an adjustable nose bridge, and both are tested to ASTM F2100 with BFE and PFE at or above 98 per cent. Aurelia Level 3 masks use the same construction at the higher fluid resistance level, which is the version procedure rooms usually specify.
Both are ear-loop formats with an adjustable nose bridge. For clinics that want a lower per-box cost at Level 2, the CliniEco three-ply Level 2 mask ships as the same Canadian-made Aurelia 2120 in its original packaging, with BFE above 99.9 per cent and 120 mmHg fluid resistance on the test report.
That is the honest position: our line is ear-loop, and if a room needs ties for retention, the right answer is to buy ties for that room rather than to make a loop work harder. The point of this article is to make that decision explicit instead of inheriting it from whatever was in the cupboard.
How the decision usually gets made, and how it should be
In most clinics the mask decision is inherited. Someone ordered a case of loops years ago, the rooms adapted, and the format has not been revisited since. The level may have been chosen correctly and the format never chosen at all.
A short review fixes it. List the rooms. For each, note how long a mask is worn and whether the wearer can step out to replace it. Rooms over an hour, or rooms where the wearer cannot leave mid-procedure, go to ties. Rooms under fifteen minutes with frequent turnover stay on loops. Then set a par level for each format and put both on the standing order.
The result is not a dramatic cost change. It is a small reduction in masks pulled per session, a reduction in the adjustments that break technique, and a stock position that matches how the rooms are actually used.
Buying for a facility? Open a wholesale and institutional account for case pricing, purchase-order billing and a named account contact, or browse the wholesale collection for case formats. Reselling? become a distributor.
References
- ASTM F2100 — Standard Specification for Performance of Materials Used in Medical Face Masks (checked 28 October 2026)
- ASTM F1862 — Standard Test Method for Resistance of Medical Face Masks to Penetration by Synthetic Blood (checked 28 October 2026)
- ASTM F2101 — Standard Test Method for Evaluating the Bacterial Filtration Efficiency (BFE) of Medical Face Mask Materials (checked 28 October 2026)
- ASTM F2299 — Standard Test Method for Determining the Initial Efficiency of Materials Used in Medical Face Masks to Penetration by Particles (checked 28 October 2026)
- ISO 22609:2004 — Clothing for protection against contact with blood and body fluids: test method using synthetic blood (checked 28 October 2026)
- ISO 10993-1:2025 — Biological evaluation of medical devices, Part 1: Requirements and general principles for the evaluation of biological safety within a risk management process (checked 4 November 2026; supersedes ISO 10993-1:2018, withdrawn 18 November 2025)
- ISO 10993-10:2021 — Biological evaluation of medical devices, Part 10: tests for skin sensitization (checked 28 October 2026)
- ISO 10993-23:2021 — Biological evaluation of medical devices, Part 23: tests for irritation (checked 28 October 2026)
- ISO 13485:2016 — Medical devices: quality management systems, requirements for regulatory purposes (checked 28 October 2026)
- ISO 2859-1:1999 — Sampling procedures for inspection by attributes, Part 1 (checked 28 October 2026)
- ISO 15223-1:2021 — Medical devices: symbols to be used with information supplied by the manufacturer (checked 28 October 2026)
- ISO 14971:2019 — Medical devices: application of risk management to medical devices (checked 28 October 2026)
- Routine Practices and Additional Precautions — Public Health Ontario (checked 28 October 2026)
- Hand Hygiene — Public Health Ontario (checked 28 October 2026)
- Personal Protective Equipment — CCOHS (checked 28 October 2026)
Printable companion: the free compliance log set includes a mask and PPE issue line, so a clinic can show what was drawn per room per day instead of estimating at reorder time.
Size the order against actual room usage with the clinic supply planner, then put the box and case quantities on the bulk quote form and compare landed cost rather than box price.
Related Reading
- Surgical Masks Wholesale Canada: Case Pricing and Par Levels for Dental Clinics
- Where to Buy Medical Face Masks in Manitoba: Levels, Case Counts and Lead Times
- EN 14683 vs ASTM F2100: Mask Standards Compared
Frequently Asked Questions
Do tie-on masks filter better than ear loop masks?
No. Filtration is a property of the mask material and construction, and both formats can be made from the same three-layer material and tested to the same ASTM F2100 level. The difference is retention and how the mask sits on a particular face, which affects leakage around the edges rather than filtration through the material.
What does ASTM F2100 actually test?
Four things: bacterial filtration efficiency, particle filtration efficiency, differential pressure (breathability) and resistance to penetration by synthetic blood. It does not test how the mask stays in place, how it fits a specific face, or how often the wearer adjusts it during a procedure.
What are the ASTM F2100 thresholds for Level 1, 2 and 3?
Level 1 requires BFE and PFE of at least 95 per cent and fluid resistance at 80 mmHg. Level 2 and Level 3 both require BFE and PFE of at least 98 per cent, with fluid resistance at 120 mmHg for Level 2 and 160 mmHg for Level 3. Differential pressure limits are stricter at the higher levels because breathability is part of the specification.
When is a tie-on mask the better choice?
Long procedures where the wearer cannot touch the mask to reposition it, sessions where a mask is worn for an hour or more, and staff whose ears cannot tolerate elastic for that long. Ties also let the wearer set the circumference, which helps where a single box has to fit many head sizes.
Why do ear loops cause so much adjustment?
Elastic loop tension is fixed by the loop length, so the mask either pulls the ears forward or sits loose. Wearers respond by touching the mask, which is the behaviour routine-practices guidance tries to avoid. A tie-on mask is knotted once and does not move until it is removed.
Can a clinic mix both formats in one clinic?
Yes, and many do: ear loops in rooms where donning speed matters, ties in procedure rooms where the mask stays on for the whole session. The purchasing implication is that both formats need a par level, and the case counts differ, so they should be separate lines on the order.
What licence should a Canadian mask supplier hold?
Medical masks are medical devices, and the establishment that imports or distributes them must hold a medical device establishment licence. CliniEco Medical holds MDEL #35334, and a buyer can ask any supplier for that number and check it before ordering.
How many masks should a clinic keep on hand?
Enough to cover the longest gap between deliveries plus a buffer for a bad week. Count masks drawn per room per day for two weeks, multiply by rooms and working days, then add the lead time in days. That number, not a rule of thumb, is the par level.
Last updated: October 2026. CliniEco Medical is a licensed medical device establishment (MDEL #35334).