Quick facts
- The common storage bands are 2-8 °C for refrigerated reagents and specimens, -20 °C for frozen reagents and -70 °C or colder for long-term nucleic acid and cell stocks; each product's label or instructions set the band that actually applies.
- ISO 15189:2022 requires a laboratory to have equipment that is fit for purpose and to monitor, maintain and record its performance, which is the clause a temperature log exists to satisfy.
- A defensible record has a minimum and a maximum, not a single daily reading: a fridge that is opened at 08:00 and checked at 16:00 looks stable and may have spent the morning at 12 °C.
- A continuous logger with an alarm is the only way to know what happened overnight; a manual twice-daily reading is a sample, not a monitor.
- An excursion is assessed on temperature, duration and the material's stability data, and the outcome is a documented disposition: released, quarantined or discarded.
- The clause numbers and storage bands were read on 2026-10-19; the ISO catalogue entry returned HTTP 200 the same day.
A laboratory refrigerator fails quietly. The door is closed, the light is on, and nothing about the room suggests that the contents have spent six hours at 14 °C. What turns that event into a manageable incident rather than a discarded week of work is the record: what the temperature was, for how long, and what the laboratory decided to do about it. This article sets out the storage bands, the monitoring frequency, the fields a log needs, the mapping check most labs skip and the excursion procedure; the specimen containers we stock for refrigerated work are the CliniEco graduated specimen cups, and the record is what makes them traceable.
Which temperature band applies to which material?
The bands are conventions, not law. Refrigerated reagents, control materials and most specimens are held at 2-8 °C. Frozen reagents are held at -20 °C, and long-term nucleic acid or cell stocks at -70 °C or below. Room-temperature storage is usually described as 15-25 °C or 20-25 °C depending on the product.
The product instructions override the convention. A reagent labelled for 2-8 °C that is placed in a -20 °C freezer may precipitate; a specimen that is meant to be frozen may be ruined by a night at 4 °C. The storage column on the product label is the first thing to read, and the second is the package insert's statement on excursions.
Blood components have their own bands, set by transfusion standards rather than by general laboratory practice, and they are outside the scope of a general reagent fridge. A laboratory that stores blood alongside reagents should separate the two physically and in the record.
| Material | Typical band | Typical monitoring | What an excursion threatens |
|---|---|---|---|
| Refrigerated reagents and controls | 2-8 °C | Continuous logger plus daily min/max | Activity loss, precipitation, pH drift |
| Frozen reagents | -20 °C | Continuous logger plus daily min/max | Freeze-thaw damage, ice crystal formation |
| Nucleic acid and cell stocks | -70 °C or colder | Continuous logger with alarm | Degradation, loss of viability |
| Microbiology media | 2-8 °C, protected from light | Daily min/max | Drying, contamination, performance loss |
| Room-temperature consumables | 15-25 °C | Daily check in hot weather | Adhesive failure, sterility pouch degradation |
How often should temperature be recorded?
There are two different questions. The first is how often a person reads and signs the record; the second is how often the device measures. A manual reading twice a day satisfies the first and misses almost everything that happens between the readings, including a door left open overnight.
A continuous data logger with a visible alarm satisfies both. It records at a set interval, keeps the history, and wakes someone when the temperature leaves the band. The manual reading then becomes a daily check that the logger is working, rather than the only evidence.
The frequency of the logger should match how fast the cabinet changes temperature. A small under-bench fridge with frequent door openings can move several degrees in minutes; a -70 °C freezer changes slowly. A fifteen-minute interval is a common compromise for a fridge, and it is enough to reconstruct an excursion.
What does a defensible record contain?
The device identifier, the location, the date and time, the reading and the initials of the person who took it. For a continuous logger, the record also needs the logger's identifier, its calibration date and the alarm set points, because a reading without a calibrated device is an opinion.
Add the minimum and maximum for the interval, and the time at which each occurred. Those two numbers are what an assessor asks for first, because they bound the excursion. A single "4 °C" at 09:00 says nothing about the previous sixteen hours.
Keep the record for the period your quality system requires and in a form that can be produced without reconstruction. A spreadsheet that is edited after the fact, with no audit trail, is weaker evidence than a signed paper sheet, even though it looks more modern.
What is a temperature mapping check, and why does it matter?
Mapping is the exercise of placing several calibrated loggers in an empty cabinet, and then in a loaded one, to find where the warm and cold spots are. Manufacturers design cabinets to be uniform, but a fridge with a full upper shelf and an empty bottom shelf is not uniform, and the difference can be several degrees.
The check answers a practical question: where should the monitoring probe sit? Putting it next to the door gives a reading that reacts to door openings; putting it in the coldest corner gives a reading that never shows a warm excursion. The probe belongs where the material is, and the mapping tells you where that is.
Repeat the mapping after a major change: a new cabinet, a repair, a change in loading pattern, or a move to a different room. A mapping done once at installation and never repeated describes a cabinet that no longer exists.
What should happen when the alarm goes off?
First, protect the material: close the door, move contents to a working cabinet if one is available, and do not open and close the door repeatedly to check. Second, record the time the alarm was noticed, the temperature at that moment and the duration if the logger can show it. Third, assess the material against its stability data.
The assessment is a documented decision, not a feeling. For each item, the question is whether the excursion exceeded the manufacturer's stated tolerance and for how long. A reagent with a two-hour allowance at 25 °C that spent forty minutes at 18 °C is releasable; the same reagent that spent a weekend at 30 °C is not.
The outcome is recorded against the item: released with the justification, quarantined pending a supplier's opinion, or discarded. A laboratory that discards without a note and a laboratory that releases without a note have the same record, which is none.
| Step | Action | Record |
|---|---|---|
| 1 | Close the door; protect the contents | Time noticed, temperature at that moment |
| 2 | Read the logger history | Minimum, maximum, duration above the limit |
| 3 | Assess each item against its stability data | Item, limit, duration, decision |
| 4 | Quarantine anything unresolved | Location, label, date, owner |
| 5 | Dispose or release with justification | Disposition, initials, date |
| 6 | Fix the cause and re-map if the cabinet changed | Work order, mapping date |
What goes wrong most often?
The probe is in the wrong place. A logger taped to the inside of the door reports the door, not the cabinet, and a logger sitting on the upper shelf reports the cold air that falls from the evaporator. The mapping check exists to prevent this, and it is the step most often skipped.
The alarm is silenced and forgotten. A logger that beeps at 03:00 and is switched off by the cleaner has recorded the event but nobody has acted on it. The alarm needs an owner and an escalation path, not just a sound.
The record is reconstructed. A month of readings filled in on the day of the audit is visible as a month of identical handwriting and identical times. A laboratory that has fallen behind should say so and fix the process, because a reconstructed record is worse than a gap.
A temperature-controlled workflow still consumes containers and transport packaging, and those are reordered alongside the log sheets. Order through the wholesale programme for case pricing and an account, or become a distributor for resale. The 90 mL graduated specimen cups sits in the same catalogue. Consumables for this line are listed under the department page.
Sources
- ISO 15189:2022, medical laboratories, requirements for quality and competence
- ISO/IEC 17025:2017, competence of testing and calibration laboratories
- CLSI M22, quality control for commercially prepared microbiological culture media
- CLSI M07, methods for dilution antimicrobial susceptibility tests
- CLSI M47, principles and procedures for blood cultures
- CLSI H21, collection, transport, and processing of blood specimens
- CLSI GP41, specimen collection (companion document)
- WHO, WHO guidelines on drawing blood: practices and procedures
- Public Health Ontario, infection prevention and control
- Health Canada, medical devices
- Medical Devices Regulations, SOR/98-282
- ISO 13485:2016, medical devices quality management
- ISO 14971:2019, application of risk management to medical devices
- Measurement Canada, calibration and measurement traceability
- CSA Group, standards catalogue
- Standards Council of Canada
Printable temperature log. One sheet per cabinet per month, with morning and evening rows, a minimum and maximum column and a space for the action taken when a reading is out of band. Print the temperature log - plain paper, no account and no sign-up, and the month's gaps are visible at a glance.
Excursion assessment builder. Enter the cabinet, the band, the time out of range and the material, and the page lays out an assessment sheet with the disposition options and a signature line. Build an excursion assessment sheet so that the decision is written down at the time rather than reconstructed afterwards.
Ask a compliance specialist. What your accreditation body expects for monitoring frequency, how to justify a release after an excursion and what to do when a logger fails are questions that depend on your scope and your province. Ask a compliance specialist - written answer specific to your equipment and province, with the regulation or standard it is based on cited.
Related reading
- Blood storage refrigerators in Canada and the US: which class applies
- Do centrifuge tubes expire? Storage and sterility in Canadian labs
- Biological indicator storage: temperature, expiry and batch
CliniEco Medical supplies eye care, laboratory and dental consumables of the kind described in this article. MDEL #35334. This article is written for laboratory managers and is not a quality manual; the storage band and the acceptable excursion for a product are set by its manufacturer, and the monitoring requirements by the standard under which the laboratory is accredited.
Frequently Asked Questions
How often should a laboratory refrigerator temperature be checked?
A continuous logger should record at intervals short enough to reconstruct an excursion, commonly every fifteen minutes for a fridge. A person should read and sign the record at least once each working day, and the logger's alarm history should be reviewed, not just the current reading.
What temperature should a lab fridge be?
2-8 °C is the usual band for refrigerated reagents and specimens. The product label or package insert sets the band that actually applies, and some reagents require a narrower range.
What counts as a temperature excursion?
Any period outside the product's stated band. The significance depends on how far outside, for how long, and what the manufacturer's stability data says the material tolerates.
Can I release material after an excursion?
Yes, if the excursion is within the manufacturer's stated tolerance and the decision is documented with the temperature, the duration and the justification. If the tolerance is unknown, quarantine the material and ask the supplier.
Why do I need a mapping study?
Mapping finds the warm and cold spots in a cabinet so that the monitoring probe sits where the material is. Without it, the probe may be measuring the door or the cold-air path rather than the storage space.
Do I need to re-map after a repair?
Yes. A new compressor, a new door gasket or a change in loading pattern can change the temperature distribution, and the previous mapping no longer describes the cabinet.