ISO 9073 Test Methods for Medical Wipes: What Each Part Measures
What a wipe specification has to answer
A purchaser who asks for "hospital-grade wipes" has described a claim, not a product. The canister in front of them carries a sheet count, an expiry date, a registration number and a contact time; what it rarely carries is the fabric data that explains why one wipe tears at the corner while another stays intact when a gloved hand scrubs a door handle.
The ISO 9073 series exists to fill that gap. It is a set of test methods for nonwovens, published in parts, each covering one measurable property. Understanding which part produces which number is the difference between buying a wipe that suits the task and buying a canister because the label used a word you recognised.
Where the wipes sit in a clinic order
Wipes are ordered with the rest of the wet consumables: the canister or refill pack, the dry washcloth case used for non-chemistry cleaning tasks, and hand hygiene at the room entrance. A 160-wipe disinfecting canister covers the treatment room surface routine, the dry 10 by 13 inch washcloth case covers the tasks that need a cloth rather than a chemistry, and the 60 mL hand sanitizer clinic pack keeps hand hygiene at the point of use. All three sit in the cleaning and disinfection range.
What ISO 9073 is, and what it is not
The series has been the reference for nonwoven testing since the 1980s and has been revised in pieces rather than as a block; Part 6, on absorption, has a 2025 edition. Each part describes an apparatus, a specimen preparation method and a way of reporting the result. That is all.
Two consequences follow. First, a lab report citing a part number is only meaningful if it also states the part's year, because a result produced against an older edition is not directly comparable with one produced against a newer one. Second, the absence of a 9073 report is not a defect: the series is voluntary, and a manufacturer may test to an internal method instead. What matters for a buyer is that the same method is used on every shipment, so a change in the fabric shows up as a change in the number.
The parts a buyer can actually use
Most of the useful information sits in a handful of parts. The table below maps the measurement to the failure it predicts.

| Part | What it measures | What it predicts for a wipe |
|---|---|---|
| 9073-2 | Thickness | How much liquid the sheet can hold and how it feels in the hand |
| 9073-3 | Tensile strength and elongation | Whether the sheet stretches or rips when pulled across a surface |
| 9073-4 | Tear resistance | Whether the wipe starts a tear at a notch or a dispenser slot |
| 9073-5 | Resistance to mechanical penetration, ball burst | Whether a fingertip pushes through during a scrub |
| 9073-6 | Absorption, capacity and rate | How much chemistry the sheet carries and how quickly it takes it up |
| 9073-8 | Liquid strike-through time | How fast liquid passes through the sheet rather than staying in it |
| 9073-10 | Lint and other particles, dry state | Whether the wipe leaves fibres on optics, glass and instrument trays |
| 9073-13 | Repeated strike-through time | How the sheet behaves on the second and third pass over the same area |
| 9073-14 | Coverstock wetback | How much liquid comes back out of the sheet under pressure |
A spec sheet does not need all nine. A wipe used on a treatment chair needs absorption, tensile and lint data. A wipe used on a screen or a lens needs lint first. A wipe used to scrub a textured floor needs tear and ball burst, because those are the two ways it will fail.
Reading an absorption number
Absorption is where supplier claims and test methods diverge most. A figure quoted as "holds 8 times its weight in liquid" is a marketing ratio; the 9073-6 style measurement reports grams of liquid taken up per unit area of fabric over a stated time, under a stated procedure.
Both numbers can be true and still describe different wipes. A heavier sheet with a lower absorption ratio can hold more total liquid than a lighter sheet with an impressive ratio, because the ratio is relative to mass and the task is relative to area. When two products are compared, the comparison only works if the same part, the same edition and the same test liquid were used — and the last one is often the missing detail, because a wipe tested against water behaves differently from one tested against a detergent solution.
Where fabric testing stops and biocompatibility starts
Nothing in ISO 9073 says anything about what the wipe does to skin or to a device surface. That question belongs to a different series, and it applies only if the product is a medical device in the first place.
ISO 10993-1 sets the framework: the evaluation is chosen by the nature of body contact and the duration of that contact, not by the material. Within that framework, Part 5 addresses in vitro cytotoxicity, Part 10 addresses skin sensitization and Part 23 addresses irritation, while Part 12 governs how samples are prepared so the results can be compared between laboratories. A wipe that contacts intact skin briefly sits in a different category from a wipe used inside a body cavity, and the test menu changes accordingly.
For a purchaser, the practical question is documentary: ask which evaluation applies to the product, and ask for the report section that covers skin contact. A supplier who can name the part numbers and the contact category has done the work; a supplier who answers with an adjective has not.

The label question: registration, claim and contact time
Canadian labels carry more regulatory information than most buyers notice. A hard-surface disinfectant is authorised with a Drug Identification Number, while products authorised as natural health products carry an NPN; the number itself identifies a specific product and claim combination, so it should be read together with the claim printed next to it.
The claim is also time-bound. A disinfectant label states the surface type and the wet contact time that the efficacy data supports, and a wipe that dries before that time has not delivered the claim. That is why absorption, evaporation and sheet size belong in the same discussion as the registration number: the chemistry cannot act on a surface that has already dried.
Published work on antimicrobial wipes has shown that test protocol and fabric binding both change the measured efficacy of the same chemistry, which is a good reason to keep a supplier's test report and the label claim attached to the same lot documentation.
What to put on your spec sheet
A working specification for a clinic is one page. It lists sheet dimensions and count, fabric mass per unit area, the test parts and editions the supplier reports, absorption figure with its test liquid, lint rating, registration number, claim and contact time, lot coding, expiry format and case configuration.
Two fields are usually omitted and matter most. The first is the test liquid, because it determines whether the absorption figure describes your use. The second is the change rule: how many surfaces a single wipe is allowed to cover before it is discarded. A specification that defines the product but not its use will be followed inconsistently no matter how well it is written.
Substrate, chemistry and the two ways wipes fail
Wipes fail in two directions. The chemistry fails when the wet time is shorter than the contact time on the label, or when the surface was not cleaned of visible soil first. The fabric fails when it tears, sheds or dries out mid-task.
Substrate choice drives the second failure. Cotton and polypropylene blends hold liquid differently from meltblown structures, and the difference shows up in wet-back and strike-through numbers rather than in the canister description. Clinics that switch substrate without re-checking those numbers often report that the new wipe "dries faster", which is a measurable property, not an opinion.
Buying for a facility? Open a wholesale and institutional account for case pricing, purchase-order billing and a named account contact at CliniEco Medical. Reselling? become a distributor.
References
- ISO 9073-2:1995 — nonwovens, determination of thickness (checked 22 October 2026)
- ISO 9073-3:1989 — nonwovens, determination of tensile strength and elongation (checked 22 October 2026)
- ISO 9073-4:1997 — nonwovens, determination of tear resistance (checked 22 October 2026)
- ISO 9073-5:2008 — nonwovens, resistance to mechanical penetration (ball burst) (checked 22 October 2026)
- ISO 9073-6:2025 — nonwovens, absorption (checked 22 October 2026)
- ISO 9073-8:1995 — nonwovens, liquid strike-through time (checked 22 October 2026)
- ISO 9073-9:2008 — nonwovens, drapeability including drape coefficient (checked 22 October 2026)
- ISO 9073-10:2003 — nonwovens, lint and other particles in the dry state (checked 22 October 2026)
- ISO 9073-13:2006 — nonwovens, repeated liquid strike-through time (checked 22 October 2026)
- ISO 9073-14:2006 — nonwovens, coverstock wetback (checked 22 October 2026)
- ISO 10993-1:2018 — biological evaluation of medical devices, evaluation and testing within a risk management process (checked 22 October 2026)
- ISO 10993-5:2009 — in vitro cytotoxicity tests (checked 22 October 2026)
- ISO 10993-10:2021 — tests for skin sensitization (checked 22 October 2026)
- ISO 10993-23:2021 — tests for irritation (checked 22 October 2026)
- ISO 10993-12:2021 — sample preparation and reference materials (checked 22 October 2026)
- ISO 15223-1:2021 — symbols to be used with medical device labels (checked 22 October 2026)
- Impact of test protocols and material binding on the efficacy of antimicrobial wipes (checked 22 October 2026)
- Public Health Ontario — environmental cleaning guidance for health care settings (PDF) (checked 22 October 2026)
- CCOHS — personal protective equipment, OSH answers (checked 22 October 2026)
Planning companion: the clinic supply planner turns your room count and wipe change frequency into cases per quarter, so the specification work below ends in an order quantity rather than a folder.
If you would rather work backwards from consumption, the supply planning calculator takes wipes per room per day and returns a monthly case figure with a reorder point.
Related Reading
- Disinfectant wipe substrate: what the wipe is made of and why it matters
- Disinfectant wipe contact time: what Canadian clinics should verify
- Quat or hydrogen peroxide: choosing disinfecting wipes for clinics
Frequently Asked Questions
What does ISO 9073 actually cover?
It is a series of test methods for nonwoven fabrics, not a product standard and not a pass-or-fail certificate. Each part describes one measurement — thickness, tear resistance, absorption, lint — so a supplier can report a number that another laboratory can reproduce. Nothing in the series tells you whether a wipe disinfects anything.
Which ISO 9073 parts matter most for a surface wipe?
The ones that describe how the sheet behaves while wet and in the hand: mass per unit area and thickness, tensile strength and elongation, tear resistance, ball burst, absorption capacity and rate, and the strike-through and wet-back tests. Lint matters on equipment and optics. Drape matters when the wipe has to reach into a narrow space.
Does a wipe need ISO 10993 testing?
Only if it is a medical device, judged by its intended use and labelling rather than by the fabric. A wipe sold to clean a device or to contact intact skin in a clinical procedure can fall inside that boundary; a general-purpose cleaning cloth sold for household surfaces does not. The manufacturer decides the classification, and a buyer can ask for the evaluation report.
What is the difference between a DIN and an NPN on a wipe label?
Both are eight-digit identifiers issued for products authorised in Canada, but they sit under different frameworks. A hard-surface disinfectant carries a Drug Identification Number; products authorised as natural health products carry an NPN. They are not interchangeable, and a number on the canister should match the product and the claim printed beside it.
Why do two wipes with the same sheet count feel so different?
Sheet count says nothing about sheet area, mass per unit area or saturation. A 160-count canister of 15 by 20 cm sheets holds roughly a third of the fabric of a 160-count canister of 20 by 30 cm sheets. Compare the sheet dimensions, the fabric weight and the stated wet weight before comparing price per canister.
How many wipes should a clinic order for a quarter?
Work from rooms and tasks rather than from habit: count the surfaces touched per room per day, multiply by the wipe change rule you actually follow, add a 15 to 20 per cent allowance for spill response, and convert to canisters using the real sheet count. A planning tool makes the arithmetic repeatable when staff change.
Can a clinic use one wipe for both a surface and a device?
That depends on the claim and the contact time, not on convenience. A disinfectant claim is tied to a surface type and a wet contact time on the label; a device surface may have a material compatibility restriction stated by its manufacturer. Where the two documents disagree, the device manufacturer's instruction governs.
Where do wipes fit in a clinic's standing order?
They behave like any wet consumable: they carry a lot number and an expiry date, they dry out if a canister is left open, and they are ordered in cases that map to a room count. CliniEco Medical supplies the Aurelia 160-wipe canister and the dry 10 by 13 inch washcloth case that many clinics pair with it.
Last updated: October 2026. CliniEco Medical is a licensed medical device establishment (MDEL #35334).