How Many Class 5 Chemical Integrators Does a Diagnostic Laboratory in Ontario Use per Month, and How Many 200 per Pack Boxes Is That? Load Count Math for a Mixed Bench

CliniEco Class 5 steam chemical integrator specification card, ISO 11140-1 Type 5, 121 to 135 degrees C

How Many Class 5 Chemical Integrators Does a Diagnostic Laboratory in Ontario Use per Month, and How Many 200 per Pack Boxes Is That? Load Count Math for a Mixed Bench

A laboratory releases a load, and a load is not a day. Eight runs in a working day are eight separate decisions about whether glassware, instruments or media go back into service, so the chemical monitoring figure follows the run sheet rather than the calendar.

The strip that carries that decision is the CliniEco steam chemical integrator - Class 5, ISO 11140-1 Type 5, 200-strip pack, yellow-to-black read with anClass 5 steam chemical integrator, 200 strips to a pack, read at the end of the cycle against an accept window.

How many Class 5 integrators does a diagnostic laboratory use in a month?

Multiply loads by working days. A community laboratory running eight loads a day across 21 working days runs 168 loads, so 168 integrators, and 2,016 across the year — ten 200-strip packs and a bit, which is eleven on the purchase order.

CliniEco Class 5 steam chemical integrator specification card, ISO 11140-1 Type 5, 121 to 135 degrees C

Loads a day Loads a month Integrators a month 200-packs a year
4 84 84 6
8 168 168 11
16 336 336 21

Why does the count track loads rather than packages?

Because the loads are not interchangeable. A laboratory sterilizes glassware, instruments and liquid media, and those differ in density, packaging and cycle type, so each released load needs its own chemical evidence. The integrator answers that at the load level through a challenge device placed at the hardest point in the chamber. The per-package indicator — an internal strip inside every Class 4 dual-indicator pouch or tray — is a separate line on the order, and a laboratory that merges the two lines into one number under-orders by a wide margin.

Four sterilization pouch sizes shown side by side

Does a Class 5 integrator get incubated?

No, and this is where buyers mix up two products. The Class 5 strip is read when the cycle ends: the colour bar either reaches the accept zone or it does not. The item that goes into an incubator is the 24-hour self-contained biological indicator, incubated for its stated read time before a load can claim a spore result. Ordering an integrator as though it came with an incubation step is how a first purchase ends up with the wrong consumable on the bench.

Which regulation applies to the order?

Not Regulation 682. R.R.O. 1990, Regulation 682, Laboratories, was revoked on July 1, 2022 under O. Reg. 45/22, so laboratory quality requirements now come from ISO 15189:2022 and from CSA Z314:23 on reprocessing. A supplier document that still cites Regulation 682 as the current rule is describing a framework that ended four years ago, and any purchasing record built on it should be corrected before an assessment finds it.

Running a diagnostic laboratory? See our laboratory consumables and sterilization supplies. Laboratories that want the release record reviewed before an accreditation visit can ask a specialist at our sterilization compliance desk.

Ordering for a clinic, lab or care home? Wholesale and multi-site ordering covers case pricing and account setup, and the B2B wholesale collection lists the lines stocked for institutional buyers. Reselling? become a distributor.

References

  1. CSA Z314:23, Canadian medical device reprocessing in all health care settings (checked 16 November 2026)
  2. ISO 15189:2022, Medical laboratories, requirements for quality and competence (checked 16 November 2026)
  3. ISO 11140-1:2014, Sterilization of health care products, chemical indicators, general requirements (checked 16 November 2026)
  4. Ontario Regulation 682, Laboratories, revoked July 1, 2022 by O. Reg. 45/22 (checked 16 November 2026)

Printable companion: the compliance log center carries a load log with one row per released load, which is the record an assessment asks for when it wants a chemical result tied to a specific cycle.

Building the monthly figure from the run sheet? The sterilization monitoring usage calculator keeps loads per day and indicators per load in separate fields so a change in bench volume shows up before the pack runs out.

Related Reading

Frequently Asked Questions

How many Class 5 integrators does a diagnostic lab use in a month?

One per released load. Eight loads a day across 21 working days is 168 loads, so 168 integrators, or 2,016 a year.

Does a Class 5 integrator get incubated?

No. It is read at the end of the cycle when the colour bar reaches the accept window; the biological indicator from the same challenge device is the item that gets incubated.

Is the count based on packages rather than loads?

Neither, in a mixed laboratory. The integrator follows the load, and the per-package indicator is a separate consumable bought against package count.

Does Regulation 682 still govern laboratory sterilization?

No. It was revoked on July 1, 2022 under O. Reg. 45/22, so requirements now come from ISO 15189:2022 and the reprocessing standard.

Last updated: November 2026. CliniEco Medical is a licensed medical device establishment (MDEL #35334).

Vous travaillez déjà avec des cliniques ? Devenez représentant régional.