Clinical Densitometers and TLC Scanners in Canada vs the US: Which Class Applies?

Graduated plastic specimen container with a screw cap on a dark background

Quick facts

  • A clinical densitometer measures the concentration of a substance on the surface of a film or support medium, either by reading light transmitted through a defined area or, in the radiochromatogram version, by mapping a radioactive element across a chromatogram.
  • In the United States it is a named entry. 21 CFR 862.2400, Densitometer/scanner (integrating, reflectance, thin-layer chromatography, or radiochromatogram) for clinical use, is Class I, product code JQT read from the openFDA classification database.
  • Canada keeps no named entry. A device intended to be used in vitro for the examination of specimens is an in vitro diagnostic device, and one intended for use in diagnosis or patient management is Class II under Part 2 Rule 4 of Schedule 1.
  • Part 2 Rule 4 lifts the class to Class III in six stated situations, including screening for or diagnosis of cancer, genetic testing, disease staging, and drug monitoring where an erroneous result would lead to an imminent life-threatening decision.
  • Part 2 Rule 7 says that where an IVDD is intended to be used with another IVDD, the class of both is the class of the higher-risk device.
  • Sections, classes and product codes below were checked against the eCFR, the Regulations and the openFDA classification database on 2026-10-16.

A clinical densitometer reads the amount of a substance held on a strip, a plate or a chromatogram. The United States names the instrument and keeps it at the lowest class; Canada asks first whether the instrument is an in vitro diagnostic device at all, and answers the class question from the words in the intended-use statement. This article sets out both routes and the records that keep a densitometer reading comparable, with the graduated specimen cups that feed the same bench.

What is a clinical densitometer or scanner?

It is a bench instrument that turns a visible or radioactive pattern into a number. In its oldest form it is a densitometer: a beam of light passes through a stained chromatogram or a stained gel and a photocell reads how much light survived, which is proportional to how much material is on the medium. In another form it is a reflectance scanner that reads the intensity of light bounced back from an opaque surface. In its most specialised form it is a radiochromatogram scanner, which moves a detector along a strip and maps where a labelled substance has settled.

The instrument is a general-purpose reader. What makes it clinical is the statement of what its output is used for: aiding in the diagnosis and treatment of a disorder, monitoring a drug level, or supporting a quality control programme. That statement is also what decides its class, in both countries, and it is the first document a purchasing officer should ask for.

Because the reading depends on the medium as much as on the optics, a densitometer is only as good as its calibration. ISO 15189:2022 sets the requirements for quality and competence in medical laboratories, and the calibration and verification of a reading instrument sit inside that framework rather than outside it.

Graduated plastic specimen container with a screw cap on a dark background

What class is a clinical densitometer in the United States?

It is a named entry. 21 CFR 862.2400 is titled Densitometer/scanner (integrating, reflectance, thin-layer chromatography, or radiochromatogram) for clinical use, and the identification describes a device intended to measure the concentration of a substance on the surface of a film or other support media, by photocell measurement of light transmission or, in the radiochromatogram scanner, by measurement of the distribution of a specific radioactive element. The regulation sets Class I (general controls).

The openFDA device classification API returns product code JQT against that section, and the FDA keeps the device in the lowest class with general controls. That is the US position: an instrument that reads a medium is treated as apparatus, even when the reading feeds a clinical decision.

Item Detail
US regulation 21 CFR 862.2400 - Densitometer/scanner for clinical use
US class Class I (general controls)
Product code JQT
Stated intended use Measure the concentration of a substance on the surface of a film or other support medium
Reading modes named in the entry Integrating, reflectance, thin-layer chromatography, radiochromatogram
Premarket route Exempt from premarket notification under subpart E of part 807, subject to section 862.9
Read on eCFR identification text and openFDA classification, both read 2026-10-16

How does Canada classify a clinical densitometer?

Canada keeps no named entry, and it also asks a prior question that the US entry does not: is this instrument an in vitro diagnostic device? An IVDD is a device intended to be used in vitro for the examination of specimens taken from the body, and an instrument that reads a patient specimen to aid a diagnosis fits that description. Once it is an IVDD, the class comes from Part 2 of Schedule 1 of the Medical Devices Regulations.

Part 2 Rule 4 reads: \\"An IVDD that is not subject to rules 1 to 3 and that is intended to be used in diagnosis or patient management is classified as Class II, unless it falls into one of the following categories, in which case it is classified as Class III.\\" The six categories are use in screening for or diagnosis of cancer, genetic testing, screening for congenital disorders in the fetus, a risk that an erroneous diagnostic result would cause death or severe disability, disease staging, and monitoring of drug or substance levels where a wrong result would lead to an imminent life-threatening decision.

That is the real class difference between the two countries. The same instrument is Class I on the FDA entry and Class II by derivation in Canada, and a stated use that reaches one of the six categories moves it to Class III. Part 2 Rule 7 adds a second consequence: an instrument intended to be used with another IVDD takes the class of the higher-risk device, so a densitometer sold with a regulated reagent kit cannot be classified in isolation.

Item Canada United States
Named entry None; classified by rule 862.2400 - Densitometer/scanner for clinical use
Class Class II (Part 2 Rule 4, diagnostic IVDD) Class I
Class III triggers Six categories, including cancer diagnosis, genetic testing and disease staging Not provided for in the entry
Use with another IVDD Part 2 Rule 7 takes the higher class of the two Not provided for in the entry
Licence route Device licence for the Class II IVDD Exempt from premarket notification, subject to section 862.9
Product code Not applicable JQT
Stacks of birch wood tongue depressors banded in paper beside a loose pile

Why does the intended use matter more than the instrument?

Because the same optics can sit in a laboratory, a factory and a clinic and only one of those placements is a medical device. A densitometer reading an industrial coating is not a medical device in Canada. A densitometer reading a patient's stained specimen to aid a diagnosis is an in vitro diagnostic device, and its class turns on the words the maker uses to describe the result. This is why a purchasing file that contains only a model number is incomplete: the classification follows the intended-use statement on the label.

The same logic explains why the calibration record is a regulatory artefact and not only a quality habit. If the class rests on the claim that the reading aids a diagnosis, then the evidence that the reading is trustworthy is part of the claim. ISO 15189:2022 puts instrument calibration and verification inside the laboratory quality system, and ISO 17511:2020 sets out how the values assigned to calibrators are made traceable.

What should a laboratory check before ordering?

Four checks. First, confirm the intended-use statement and whether it names diagnosis, patient management or one of the six Class III categories. Second, confirm the reading modes the maker supports, because integration, reflectance and transmission require different reference materials. Third, confirm the calibration and verification material that ships with the instrument, and whether the maker supplies traceability documentation under ISO 17511:2020. Fourth, confirm the specimen handling the workflow expects: the container, the closure, the transport condition and the labelling, because a correct reading of a mislabelled specimen is still a wrong result.

Check What to ask for Why it matters
Intended-use statement Label text, not the catalogue heading Decides the Canadian class and the Class III triggers
Reading modes Transmission, reflectance or radiochromatogram Each needs its own reference material
Calibration Traceability documentation and interval ISO 17511:2020 governs value assignment
Verification Method and acceptance criteria ISO 15189:2022 places this inside the quality system
Consumables Specimen container, closure and label A mislabelled specimen is a wrong result
Records Instrument log, calibration log and results The evidence an inspection asks for first

Benches that run densitometry stock the same surrounding consumables as any other bench. The graduated 90 mL specimen cups, the 120 mL sterile screw-cap container and the 15 mL sterile centrifuge tubes belong to the same ordering line.

A clinical laboratory also reorders the consumables used at the same bench. Clinics that stock for a whole practice can order through the wholesale programme and request a bulk quote for a standing or annual order; the graduated 90 mL leak-proof specimen cups sits in the same catalogue. Consumables for this line are listed under diagnostic laboratories. Reselling? become a distributor.

Sources

  1. openFDA device classification API
  2. Medical Devices Regulations, SOR/98-282, full text and Schedule 1
  3. US FDA, medical device databases
  4. US FDA, overview of device regulation
  5. Health Canada, medical devices
  6. Health Canada, establishment licensing
  7. ISO 15189:2022, medical laboratories, requirements for quality and competence
  8. ISO 17511:2020, metrological traceability of values assigned to calibrators
  9. ISO 13485:2016, medical devices quality management
  10. ISO 14971:2019, application of risk management to medical devices
  11. ISO 11137-1:2006, radiation sterilization of health care products
  12. ISO 20776-1:2019, susceptibility testing of infectious agents
  13. Clinical and Laboratory Standards Institute
  14. World Health Organization
  15. US CDC, laboratory quality
  16. Public Health Ontario, infection prevention and control
  17. Standards Council of Canada

Printable record sheet. An instrument log is the first page an assessor asks for and the last page anyone writes on. download the instrument and calibration log sheet — the pack has an instrument register, a calibration and verification page and a results review line; it prints on plain paper and no account and no sign-up is required to open it

Log generator. Name the instrument, its reading mode and your province, and the page builds a dated log whose header repeats those details on every sheet. generate an instrument log you can print — it numbers each page, carries the mode and the calibration due date, and leaves the verification columns blank for the analyst

Ask a compliance specialist. A classification question usually turns on how the device is used, not only on its name. Ask a compliance specialist — you get a written answer specific to your equipment and province, with the regulation or standard it is based on cited.

Related reading

CliniEco Medical supplies eye care, laboratory and dental consumables of the kind described in this article. MDEL #35334. This article is written for optometry, laboratory and dental procurement professionals and is not legal advice; the class of a device and the records a practice keeps belong to the manufacturer and to the requirements that apply to it.

Frequently Asked Questions

What class is a clinical densitometer in the United States?

It is 21 CFR 862.2400 at Class I (general controls) with product code JQT, and it is exempt from premarket notification under subpart E of part 807, subject to section 862.9.

What class is a clinical densitometer in Canada?

It is treated as an in vitro diagnostic device used in diagnosis or patient management, and Part 2 Rule 4 of Schedule 1 of the Medical Devices Regulations places it at Class II.

When does a densitometer reach Class III in Canada?

When its intended use falls into one of the six categories listed in Part 2 Rule 4, such as screening for or diagnosis of cancer, genetic testing, disease staging, or drug monitoring where an erroneous result would lead to an imminent life-threatening decision.

Does the scanner take the class of the reagent it is used with?

It can. Part 2 Rule 7 provides that where an IVDD, including its analyzers and reagents, is intended to be used with another IVDD, the class of both is the class of the higher-risk device.

What else is a clinical densitometer called?

Scanner, integrating densitometer, reflectance scanner, TLC scanner, radiochromatogram scanner and gel documentation instrument. The class follows the intended-use statement.

What records does the laboratory need for one?

An instrument register, a calibration and verification log with traceability to ISO 17511:2020, a results review line, and the specimen handling records that ISO 15189:2022 expects inside the quality system.

Vous travaillez déjà avec des cliniques ? Devenez représentant régional.