A practice manager in Mississauga had her spore test records in a binder, sorted by month. The infection control auditor asked one question: "Show me the load that ran last Tuesday at 2 pm, and tell me who read the result." The binder had the test result. It did not have the load number. That single gap turned a fifteen-minute review into a written finding, and the finding was not about sterilization quality — the sterilizer was working. It was about evidence.
An incubator is the easiest piece of the sterility assurance chain to buy and the hardest to document. It holds vials at 56–60 °C for a day, and it does nothing else for the file unless someone writes down what it held, when, and against what. This is the record set Canadian auditors ask for, in the order they ask for it.
What does an auditor actually ask about a BI incubator?
The incubator itself is rarely the subject. The subject is the chain: was the indicator incubated at the required temperature for the full readout, was the temperature verified against something traceable, was each biological indicator traceable to a specific load, was the result read and initialled by a named person, and what happened when a result came back positive.
Ontario's dental standard of practice is explicit that the daily operation of every sterilizer must be reviewed and documented, and that the log book must be kept for at least 10 years from the date of the last entry in that record. Public Health Ontario's provincial reprocessing guidance adds the operating rule that most clinics miss: a biological indicator is used to test the sterilizer each day that it is used and with each type of cycle used that day. A clinic running a wrapped cycle and a hollow-load cycle on the same morning owes the file two indicators, not one.
Five records cover all of it. Each one is a single line on a form — which is the point. If a record needs a paragraph to explain, it will not survive a busy Tuesday.
Which two incubation formats do these records cover?
The record set below applies to either format: a purpose-built biological indicator incubator with a dry block sized for self-contained vials, or an incubator shared with other incubation work. Both are stocked in Canada and both are documented the same way; what changes is only where the temperature record comes from.

CliniEco 24-hour biological indicator incubator — 24-well dry block, USB export

DLAB HB105-S1 dry bath incubator — 20-well block with lid
Record 1 — What temperature did the incubator actually hold?
Write the setpoint and the measured value as two numbers, not one. The setpoint is what the panel says; the measured value is what a reference probe reads inside the block. Both belong on the sheet, together with the time of the check and the initials of the person who took it.
Why the distinction matters: a dry-block incubator with ±0.5 °C control accuracy can sit inside its own tolerance and still be outside the window your biological indicator needs. Self-contained indicators for steam cycles carry Geobacillus stearothermophilus spores, and the incubation temperature specified for that organism is the number the package insert states — for most 24-hour vials it is 56–60 °C (ISO 11138-3 sets the biological indicator requirements, and the manufacturer's insert sets the incubation condition). Recording a setpoint of 57 °C proves nothing unless something independent confirmed the block was at 57 °C.
One honest note about hardware. The DLAB HB105-S1 dry bath holds temperature and time on its display but does not log or export data — the manufacturer's own documentation says so, and we would rather state it here than have a clinic discover it during an inspection. Your load sheet is the record. Units that do export, such as the CliniEco 24-hour incubator with USB data export, still need the sheet; the export is corroboration, not a replacement for a signed line.
Record 2 — Which BI lot went into which load?
Three fields, and clinics routinely have two of them. The biological indicator lot number and expiry date come off the vial label; the certificate of analysis for that lot carries the measured spore population and D-value, which is what makes the test meaningful (ISO 11138-1 governs how those values are declared). The third field is the load identifier.
That identifier has to match the package label, because the auditor's next move is to pull a pouch off the shelf and read it back to you. Ontario's dental standard requires each package to be labelled with the date reprocessed, the sterilizer used, the cycle or load number and the initials of the person who reprocessed it, applied in a way that does not puncture or dampen the package; where the instruments are not visible, the contents must be labelled too. If the pouch says load 14 and the log says load 13, the auditor is entitled to treat the record as reconstructed after the fact.
Record 3 — When did incubation start, and who read the result?
A 24-hour readout is 24 hours of incubation plus a reading, and both halves need a time and a name. Record the time the vial went into the block, the time it came out, the result, and the initials of the reader. For rapid-readout fluorescence indicators — which can return a result in one hour — record the reader, the well position and the readout interval used, because a result that cannot be tied to a specific instrument and well is a result someone else could have produced.
This is also where clinics confuse two different claims. Physical and chemical indicators do not ensure that sterilization has been achieved; they verify that the necessary conditions were met. A biological indicator answers the narrower, stronger question: did this cycle type, on this day, on this sterilizer, kill the resistant spores it was challenged with. Chemical indicators do not replace the need for a biological indicator, and "the strip changed colour, so the load is sterile" is not a defensible sentence in a file.
Record 4 — How was the incubator temperature verified, and against what?
Verification is not calibration, and the file needs both distinguished. Verification is a routine check — a reference thermometer or a PT1000 probe in a well, logged at a set interval. Calibration is the periodic, traceable service that ties the instrument's reading to a national standard, performed by a provider who issues a certificate with an uncertainty statement.
Write four things: the date, the method and instrument used, the reading obtained, and the action taken if the reading fell outside tolerance. A clinic that cannot show a tolerance figure has no way to say whether a reading was acceptable, which means every reading in the file is unaudited. Vials incubated outside the specified range are not valid results — they are a retest, and the retest belongs in the same record.
Record 5 — What happened when a result came back positive?
A positive biological indicator is not a paperwork event. Ontario's standard lays out the sequence: stop using the sterilizer, review the physical and chemical indicator records since the last negative result, retest immediately using the same cycle, and return the unit to service only when the repeat is negative and the indicators are acceptable. Implant loads are held in quarantine until the result is known.
What the auditor wants from this record is not the outcome — negative repeats are common and are not a failure of the clinic. What the auditor wants is proof that the sequence ran: the date the positive appeared, the unit taken out of service, who was notified, what the retest showed, and the date the unit returned to use. A file that jumps from positive to normal operation with nothing in between is the finding.
Which incubator specifications belong on the record sheet?
Three columns of the sheet are hardware facts, and they should be copied from the manual rather than remembered:
| Specification | CliniEco 24-hour BI incubator | DLAB HB105-S1 dry bath |
|---|---|---|
| Well count and bore | 24 wells, 8.8 mm, matched to standard self-contained vial diameter | 20 wells, 11 mm block for 8.8 mm tubes |
| Temperature control | 56–60 °C, ±0.5 °C, PID control with NTC sensor | 56–60 °C, ±0.5 °C accuracy, ±0.5 °C uniformity at 37 °C |
| Data output | LCD display plus USB data export | Display only — no logging or export; record on your load sheet |
| Electrical approval | 100–240 V AC external adapter, 50/60 Hz | cTUVus, TÜV Rheinland certificate CU 72205506 0001, tested to UL 61010-1 and CAN/CSA-C22.2 No. 61010-1-12; FCC Part 15 Subpart B and ICES-001 |
| Verification option | Reference-probe check through a loaded well | Supports a PT1000 external sensor for a reference read |
What does the auditor ask, what do you produce, and what does a gap cost?
| Question asked | What you produce | What a missing record means |
|---|---|---|
| Was the indicator held at the required temperature? | Setpoint and measured value, with time and initials | No basis for claiming the result is valid; retests are unprovable |
| Is the temperature traceable? | Verification log plus calibration certificate with uncertainty | The instrument's readings become opinion |
| Is the BI traceable to the load? | Vial lot and expiry, certificate of analysis, cycle or load number matching the pouch label | Record treated as reconstructed after the fact |
| Who read the result, and when? | Incubation start, read time, reader initials, reader and well for rapid readout | The result has no owner — a citable deficiency |
| What did you do on a positive? | Out-of-service date, notifications, retest, return-to-service date | Quarantine and corrective action cannot be evidenced |
Where do the five records live, and for how long?
One book per sterilizer, kept with the reprocessing area rather than in an office drawer, because the auditor asks for it at the sterilizer. Entries carry initials, not signatures, and the initials must be listed somewhere the auditor can resolve them to a name. Retention in Ontario's dental standard is at least 10 years measured from the last entry, so a book is never closed when a unit is replaced — it is closed 10 years after its final line.
Practices running more than one sterilizer should keep one book per unit and write the serial number inside the cover. When a second cycle type is introduced, add a column rather than a second book. Auditors read columns faster than they read binders.
Where to buy biological indicator incubators in Canada
CliniEco Medical supplies both incubation formats to dental practices, clinics and laboratories across Canada, shipped from Toronto.
Facilities ordering for several treatment rooms can open a wholesale clinic account for volume pricing and standing deliveries. Both formats are supported by the free sterilization log and template centre, which carries the record sheet described above, and by the sterilization self-check tool for a quick review of what your file currently proves. Facilities that want the file reviewed against their cycle types can book a sterilization compliance consultation. Reselling? become a distributor.
Related reading: how to choose sterilization pouches: sizes, materials and seal types — the packaging side of the same traceability chain — and BI versus chemical indicators in sterilization monitoring, which explains which indicator answers which question.
Frequently asked questions
Do I need a data-logging incubator to pass an inspection?
No. What an inspection requires is a signed record of the temperature held, the traceability of that reading, and the result with a reader's initials. A logging instrument makes that record easier to corroborate, but a unit without logging is acceptable if the manual says so and the clinic keeps the load sheet. What is not acceptable is claiming a device logs data when it does not.
How many biological indicators do I run in a day?
One per sterilizer per day that it is used, and with each type of cycle used that day. A clinic that runs a wrapped cycle in the morning and a hollow-load cycle in the afternoon runs two. Ontario's standard applies the 10-year retention to the log that records both.
Can I use a laboratory incubator or an oven instead?
An incubator has to hold the temperature the indicator's package insert specifies, within a tolerance you can document, and it has to do so uniformly across the vials in the block. A general-purpose oven or a water bath introduces variables — uneven wells, evaporation, contamination — that an auditor can question and that a dry block designed for self-contained vials does not. If a device has no stated uniformity figure, the file cannot show that every vial saw the same conditions.
What belongs on the certificate of analysis for a BI lot?
The measured spore population, the D-value, the lot number and the expiry. Keep it with the log rather than with the shipping paperwork, because it is the document that makes the lot's result interpretable — ISO 11138-1 governs how those values are declared, and an auditor who asks about a specific lot will expect the paper that came with it.
Reference sources
- Royal College of Dental Surgeons of Ontario, Infection Prevention and Control in the Dental Office (Standard of Practice, 40 pp.) — daily sterilizer documentation, package labelling four elements, 10-year log retention, positive-BI response; checked 30 October 2026. RCDSO IPAC standard (PDF)
- Public Health Ontario / PIDAC, Cleaning, Disinfection and Sterilization of Medical Equipment/Devices in All Health Care Settings, 3rd edition (May 2013) — biological indicator each day used and each cycle type used, record and initial results, rapid readout in one hour, chemical indicators do not replace biological indicators; checked 30 October 2026. PIDAC reprocessing guidance (PDF)
- ISO 11138-1:2017 — Sterilization of health care products, biological indicators, general requirements; checked 30 October 2026. ISO 11138-1:2017 catalogue record
- ISO 11138-3:2017 — biological indicators for moist heat sterilization processes; checked 30 October 2026. ISO 11138-3:2017 catalogue record
- ISO 11140-1:2014 — chemical indicators, general requirements (Classes 1–6); checked 30 October 2026. ISO 11140-1:2014 catalogue record
- ISO 17665:2024 — moist heat sterilization, requirements for the development, validation and routine control of a sterilization process; checked 30 October 2026. ISO 17665:2024 catalogue record
- CSA Z314 (medical device reprocessing) is referenced in the text by designation only; the standard is distributed through CSA Group and its full text is not publicly hosted.
- Hardware specifications are taken from the CliniEco 24-hour incubator and DLAB HB105-S1 product documentation held on this site, checked 30 October 2026.
CliniEco Medical is a licensed medical device establishment (MDEL #35334).