Quick facts
- A washer-disinfector is validated for a configuration: the unit, the load, the chemistry, the water and the selected cycle. Change the load pattern and the earlier evidence no longer describes what ran.
- The CDC guideline states the loading rules in one sentence: hinged instruments opened fully, no stacking, disassembly as far as possible, so that detergent solution reaches every surface.
- Cleaning performance in the published literature is measured on surfaces that had adequate contact with the water flow — which makes racking a process variable, not a housekeeping preference.
- Canadian provincial guidance allows a washer-disinfector for low-level disinfection and states plainly that it is not to be used for high-level disinfection, so a washer cycle is not a substitute for a semi-critical device process.
- There is no real-time test that verifies cleaning in a clinical setting; the evidence is a validated process, periodic test runs and a visible inspection of every instrument.
A washer-disinfector either produces a clean load or a load that looks clean, and the difference is almost never the machine. It is how the instruments sat in the racks, whether hinges were open, whether lumens were connected to a flushing port, which cycle was selected, and what the water and detergent were doing on the day. Those inputs are also what a validation run tests, which is why a facility cannot validate "the machine" once and then load it however it likes.
This article sets out the loading rules that decide whether cleaning performance is reachable, the cycle selection decisions that decide whether the result is appropriate for the device, and the events that return a validated process to an unvalidated one. It assumes the reader already knows what A0 measures; the arithmetic behind A0 and the values the standards carry are treated separately in the A0 values article, so this piece stays on configuration.
Configuration starts before the machine: soil that has dried on an instrument is harder to remove in any washer, which is why point-of-use treatment and an enzymatic soak are part of the process rather than a convenience. An enzymatic ultrasonic cleaning solution used at the concentration the manufacturer specifies is the chemistry side of that step, and the concentration is one of the inputs a validation run is checking.
What is a washer-disinfector cycle actually validated against?
A washer-disinfector validation is a test of a process, and the process has five inputs: the unit, the load as presented, the chemistry, the water, and the cycle parameters. ISO 15883-1:2024 carries the general requirements, terms, definitions and tests for washer-disinfectors, and ISO 15883-2:2024 carries the requirements and tests for units that clean and thermally disinfect reusable critical and semi-critical devices in a single operating cycle — surgical instruments, anaesthetic equipment, and the bowls, dishes, receivers, utensils and glassware used with them. The second part is explicitly written to be used alongside the general requirements in Part 1.
Two features of that structure matter at the bench. First, the standard is written around a device population, so a cycle that is appropriate for a solid bowl is not automatically appropriate for a hinged rongeur or a cannulated drill. Second, the test methods are defined separately from the performance claim: ISO 15883-5:2021 covers the test soils and methods used to demonstrate cleaning performance, which is the reason a validation run uses a defined soil rather than a visual judgement.
Neither part of the family covers prion inactivation. ISO 15883-2:2024 says so in a note, and the practical consequence is that a washer-disinfector cycle cannot be described as reducing transmissible spongiform encephalopathy risk, whatever the thermal parameters. Devices exposed to high-risk tissue follow a separate route in Canadian guidance.
How does loading change whether cleaning can be validated?
The published evidence is unusually direct. The CDC guideline describes a study in which cleaning, measured as a 5 to 6 log10 reduction, was achieved on surfaces that had adequate contact with the water flow in the machine. Surfaces that the spray did not reach did not achieve that reduction, and no amount of detergent compensates for a shadowed surface.
The same guideline then states the loading rules in operating language: when a washer-disinfector is used, hinged instruments should be opened fully to allow adequate contact with the detergent solution, stacking of instruments in washers should be avoided, and instruments should be disassembled as much as possible. Those three sentences cover most of the failures that get attributed to the machine.
| Rule at the rack | Why the process depends on it | What to check before closing the door |
|---|---|---|
| Open every hinge, ratchet and box lock | A closed hinge shields two surfaces from the spray and from the detergent | Each instrument opened to its full working position, not merely unlocked |
| Do not stack trays or nest instruments | Stacking creates shadows and traps water in the upper tray's base | One layer per rack position, no tray resting on instruments |
| Disassemble where the manufacturer allows it | Components joined together hide the surfaces between them | Removable parts separated and placed in the rack's small-parts holder |
| Present lumens to a flushing port | Fluidics, not spray, is what reaches an internal channel | Connectors seated, correct port, flow confirmed where the unit reports it |
| Angle hollow items to drain | Retained water dilutes the rinse and dries poorly | Openings facing down or to the drain path, no upward-facing cups |
| Keep instruments off the rack floor | Contact points are unwashed points | Instruments in inserts or on pins, not lying flat on the mesh |
| Load delicate items so they cannot move | Movement during the cycle damages tips and blocks spray arms | Tip protectors where the manufacturer permits them, spray arms free to rotate |
| Do not overload to save a run | Overloading reduces the flow that the performance claim depends on | Rack pattern matches the validated pattern for that rack |
| Keep the load type consistent with the cycle | Mixed loads may need incompatible parameters | Metal with metal; rubber, plastic and anaesthetic goods in the cycle their instructions name |
| Record what was loaded, not just that a cycle ran | A record without the load pattern cannot support the release decision | Cycle, rack, load type and operator on the load record |
The lumen row is where validation and practice separate most widely. Canadian provincial guidance requires lumen devices to be brushed according to the manufacturer's instructions, flushed manually or mechanically with detergent, rinsed, checked for obstruction and leakage, and dried with filtered compressed air. It also asks for the final rinse of lumen devices to use commercially prepared sterile, pyrogen-free water, with the explicit warning that distilled water is not necessarily sterile or pyrogen-free. A washer-disinfector with a flushing rack can perform part of that sequence; it does not remove the need to check the channel afterwards.
Ultrasonic cleaning sits alongside the washer rather than inside it. Provincial guidance strongly recommends ultrasonic cleaning for semi-critical or critical devices with joints, crevices or lumens, requires complete immersion, and asks for the solution to be changed at least daily or more often if it becomes visibly soiled. A benchtop ultrasonic cleaner is the unit most clinic settings use for that step before the washer or before packing.
Which cycle should the load actually run?
Cycle selection is a device decision before it is a machine decision, and three questions settle most cases.
The first is the level of processing the device needs. Canadian provincial guidance states that a washer-disinfector may be used for low-level disinfection and that it is not to be used for high-level disinfection. That sentence resolves a recurring confusion: a washer cycle that thermally disinfects a solid instrument is a cleaning and low-level process, and it does not convert a semi-critical device into a ready-to-use one where high-level disinfection is required.
The second is the temperature the device can survive. Thermal disinfection is a heat process, and the manufacturer's instructions define what the device will tolerate. Where an instrument has a temperature limit below the disinfection stage, the device belongs in a different process, not in the same cycle at a lower setting that nobody validated.
The third is what the cycle has to prove. A thermal disinfection stage is described by its A0 value, and the 2024 edition of ISO 15883-1 raised the minimum temperature at which thermal disinfection and A0 calculation apply from 65 °C to 70 °C. A cycle justified with a 65 °C reference is citing an earlier edition, which is a documentation defect even when the machine runs correctly.
| Device type | Processing the device needs | Cycle that fits | What disqualifies the cycle |
|---|---|---|---|
| Solid stainless instruments, no joints | Cleaning plus low-level disinfection where the device is non-critical; cleaning before sterilization where it is critical | Standard instrument cycle with a thermal disinfection stage | Overloading, mixed metal load presented at an angle that traps water |
| Hinged instruments, box locks, ratchets | Cleaning with full surface access | Instrument cycle with hinges opened and inserts used | Hinges closed, instruments nested, insert omitted |
| Lumened instruments, cannulae, suction tips | Cleaning with fluidics through the channel, then inspection | Cycle with flushing rack and lumen connectors | Connector missing, wrong port, lumen not checked after the cycle |
| Anaesthetic goods, rubber and plastics | Cleaning at a temperature the material tolerates | Cycle named by the device manufacturer | A metal cycle run at a temperature above the material's limit |
| Bowls, dishes, receivers, utensils, glassware | Cleaning plus thermal disinfection as non-critical items | Utilities cycle | Glassware unrestrained, mixed with heavy instruments |
| Devices with a stated temperature ceiling | Cleaning, with disinfection by another validated method | Cycle below the ceiling, disinfection elsewhere | Any cycle that exceeds the ceiling because "the load looked similar" |
| Devices the manufacturer says cannot be immersed | Manual cleaning, then the process the instructions name | Not a washer cycle | Any immersion, however brief |
The last row is the one that gets argued about. Immersion is a process decision, and a device whose instructions exclude immersion does not become immersible because the rack has a holder for it.
When does a validated process stop being validated?
A validation covers the configuration that was tested. Anything that changes an input to that configuration is a reason to re-establish the evidence rather than to assume it carries over.
| Trigger | What the earlier validation covered | What has to be re-run |
|---|---|---|
| A new device family or a new rack pattern | The load as previously presented | Performance qualification with the new load, including the worst-case position |
| A change of detergent, concentration or dosing control | The chemistry that was tested | Cleaning performance tests with the new chemistry at the specified dose |
| A change in the water supply or treatment | The water quality that was tested | Final rinse checks and the cleaning tests that depend on water quality |
| Major repair or replacement of pumps, spray arms, dosing or heating | The unit as tested | Installation and performance qualification before routine use resumes |
| Relocation, or work on the room's services | The installation as tested | Installation qualification at the new position, then performance qualification |
| A failed routine test or a failed cleaning check | Nothing: the assumption is broken | Investigation, corrective action, then a repeat run with the same test method |
| A change in the process chemicals used for pre-cleaning | The soil removal step feeding the washer | Cleaning tests on the worst-case soil, not only on visibly clean instruments |
| A new reprocessing procedure written after an audit finding | The documented process | Verification that the documented process is the one that runs, then performance tests if parameters changed |
Two of those triggers are organisational rather than technical: a repair and a relocation are both events where the unit comes back looking identical and is treated as if nothing happened. The service report is the document that says otherwise, and it should live in the same file as the qualification results.
How is cleaning verified if there is no real-time test?
The CDC guideline is blunt about the limit: no real-time test exists that can be employed in a clinical setting to verify cleaning, and the only way to establish adequacy is a reprocessing verification test in a laboratory programme, through methods such as microorganism detection, chemical detection for organic contaminants or protein residue. At a minimum, all instruments should be individually inspected and be visibly clean.
The same guideline reports residual protein measurements that make the point better than any inspection habit: median residual protein per instrument across five trays was 267, 260, 163, 456 and 756 micrograms, and median amounts across hospitals ranged from 8 to 91 micrograms. Instruments that pass a visual check can still carry a measurable protein load, which is why the release decision rests on a validated process and a documented test method rather than on appearance.
That is also why ISO 15883-5:2021 matters in a facility's file. It defines the test soils and methods used to demonstrate cleaning performance, so a validation report that names the soil and the method is auditable, and a report that says "visually clean" is not.
Loading and cycle records close the loop. A load record that names the cycle, the rack pattern, the load type and the operator is what connects a validated configuration to a specific run; a record that logs only that a cycle completed cannot support anything. The compliance log centre holds the same field set in a browser page and prints blank for a binder, and the sterilization compliance hub places the washer, sealer, sterilizer and monitoring documents in one frame.
What does this change on the shelf?
Three consumable decisions follow from the loading and cycle rules, and each has a process consequence rather than a price consequence.
The chemistry has to be dosed, not guessed. A concentration that varies by feel makes the cleaning step unverifiable, and the detergent is one of the five inputs a validation tests. The second is the pre-cleaning step for lumens: a brush that matches the channel, and a flush that reaches it. The third is the pack: instruments that come out of the washer and go into storage need a packaging format whose seal is validated, and a Class 4 self-sealing pouch records exposure on the pack while the washer record covers the load.
Ordering for a clinic, a laboratory or a care home? Wholesale and multi-site ordering covers account setup and delivery across sites, and the B2B wholesale collection lists the lines stocked for institutional buyers. Reselling? become a distributor.
Have a question about your own facility? Whether a specific load can be validated in your unit is a question about your configuration, not about the standard in the abstract. Ask your compliance question and you will get a written answer citing the document it rests on.
Related reading
- Reading an A0 claim on a washer-disinfector cycle record — the arithmetic behind the number on the printout.
- A dental lab's washer-disinfector validation run failed: what to check before blaming the machine — the same inputs, read from the failure side.
- ISO 15883-1:2024 washer-disinfectors and Canadian practice — the standard's own structure, part by part.
- Benchtop ultrasonic cleaner or central washer-disinfector: when a practice should upgrade — the capacity question that sits underneath the cycle question.
Frequently Asked Questions
Can a washer-disinfector be validated for all loads at once?
No. Validation covers a configuration, and the load as presented is one of its inputs. A facility normally validates the load families it actually processes and identifies the worst-case position within each — the rack spot that is hardest to reach — then reproduces that pattern in routine use. A new load family or a materially different rack pattern is a reason to re-establish performance evidence for that configuration.
Why does stacking trays cause a cleaning failure?
Because the performance claim rests on contact with the water flow. Published measurements show cleaning in the range of a 5 to 6 log10 reduction on surfaces that had adequate contact, and a stacked tray shields the surfaces underneath from both the spray and the detergent solution. The CDC guideline names stacking as something to avoid, alongside closed hinges and assembled instruments.
Does a thermal disinfection stage make a semi-critical device ready to use?
Not on its own. Canadian provincial guidance states that washer-disinfectors may be used for low-level disinfection and are not to be used for high-level disinfection. A semi-critical device that requires high-level disinfection needs the process its manufacturer's instructions name, which is a different route from a washer cycle with a thermal stage.
Is 65 °C still a valid thermal disinfection reference?
It is a reference to an earlier edition. ISO 15883-1:2024 raised the minimum temperature at which thermal disinfection and A0 calculation apply from 65 °C to 70 °C. A procedure or validation report that justifies a cycle with a 65 °C figure is describing the previous edition, and the citation should be corrected even where the cycle itself reaches a higher temperature.
How often must the washer-disinfector be revalidated?
Revalidation is triggered by change rather than by the calendar: a new load family, a different detergent or dosing arrangement, a change in water supply, a major repair, relocation, or a failed routine test. Routine periodic testing continues in between, and the manufacturer's schedule and the requirement of the authority governing the facility set its frequency.
What does a cleaning validation actually measure?
Residual soil on test pieces, using a defined soil and a defined method — the territory of ISO 15883-5:2021 — or protein residue measured in a laboratory programme. The CDC guideline notes that no real-time test verifies cleaning in a clinical setting, and reports median residual protein figures that vary by tray and by hospital, which is the reason a validated process and an individual instrument inspection are both required.
Every CliniEco Medical product is manufactured under an ISO 13485 quality management system and distributed under Health Canada MDEL #35334. If your question is whether a specific load can be validated in a specific unit, our specialists will read the standard with you rather than paraphrase it.
Sources
- ISO 15883-1:2024, washer-disinfectors: general requirements, terms and definitions and tests
- ISO 15883-2:2024, washer-disinfectors: requirements and tests for units employing thermal disinfection for critical and semi-critical medical devices
- ISO 15883-5:2021, washer-disinfectors: test soils and methods for demonstrating cleaning efficacy
- CSA Z314:23, Canadian medical device reprocessing in all health care settings
- Public Health Ontario, PIDAC-IPC advisory on cleaning, disinfection and sterilization of medical equipment and devices in all health care settings, 3rd edition
- Public Health Ontario, reprocessing steps fact sheet
- Centers for Disease Control and Prevention, guideline for disinfection and sterilization in healthcare facilities
- ANSI/AAMI ST79, steam sterilization recommended practice
- ISO 17664-1:2021, information to be provided by the medical device manufacturer for processing
- Public Health Ontario, IPAC checklist for dental practice: reprocessing