Pouring Agar Plates In-House or Buying Them Prepared: A Decision Guide for Canadian Labs

Clear graduated specimen container with a white screw cap, marked in ounces and millilitres

Quick facts

  • A prepared plate is a manufactured product with a lot number, a release test and an expiry date. An in-house plate is a laboratory preparation with the same quality obligations but no supplier's release certificate.
  • ISO 11133:2014 covers the preparation, production, storage and performance testing of culture media, and CLSI M22 covers quality control of commercially prepared microbiological culture media.
  • For disk diffusion, CLSI M02 works from an agar depth of about 4 mm, which is a volume-to-area relationship rather than a fixed volume per plate.
  • A 90 mm plate holds about 63.6 cm² of agar surface; 25 mL gives a depth of about 3.9 mm, and 30 mL gives about 4.7 mm. Overfilling changes the depth and can shift zone diameters.
  • Prepared plates need storage at the temperature on the label, normally 2-8 °C, and must not be frozen. In-house plates need the same storage plus a release decision before use.
  • ISO 15189:2022 puts media in the resource requirements and expects the laboratory to verify that each lot performs as intended before it is used for patient testing.

The choice between pouring agar plates in-house and buying them prepared is usually presented as a cost question, and it is not: it is a question about who performs the release testing and how much flexibility the laboratory actually needs. A purchased plate arrives with a lot number, a quality control release and an expiry date. A plate poured on the bench is the laboratory's own product, with the same obligations and none of the supplier's paperwork. This article sets out the quality checks each route requires, the volume and labour arithmetic that decides the break-even, and the storage rules that determine whether either route works in a small Canadian laboratory; the specimen containers used alongside the bench are in the 90 mL graduated cup range, and the standards cited below are the ones an assessor will name.

What is actually different between a bought plate and a poured plate?

A commercially prepared plate is produced under a quality system, released against a specification, labelled with a lot number and an expiry date, and shipped under a controlled temperature. The laboratory still has to verify that the plate performs for its intended use, but the manufacturer has done the formulation, the sterilisation and the release testing.

A plate poured in-house is made from dehydrated medium or from raw ingredients, reconstituted, sterilised, cooled, poured, solidified and stored. The laboratory owns every step, including the sterility check, the pH check, the depth check and the growth-promotion test. The work is not difficult, but it is work that has to be scheduled.

The regulatory framing is the same on both routes. ISO 11133 describes the preparation and performance testing of culture media, CLSI M22 describes the quality control of commercially prepared media, and ISO 15189 expects the laboratory to verify that the media it uses are fit for the method. The difference is who signs the release.

Item Bought prepared Poured in-house
Formulation and sterilisation Supplier Laboratory
Lot release testing Supplier, with certificate Laboratory
Sterility check Supplier, plus laboratory acceptance Laboratory, every batch
Depth and pH check Supplier Laboratory, every batch
Shelf life Supplier's expiry, often weeks Short, and set by the laboratory
Flexibility Fixed formats and volumes Any formulation, any volume
Labour Handling and storage Preparation, pouring, cleaning, release

How much labour does pouring actually take?

The arithmetic is unglamorous and decisive. A batch of 20 plates takes perhaps 30 to 45 minutes of hands-on time including preparation, sterilisation, cooling, pouring and cleanup, plus the release checks the next day. That is before the sterility incubation and the growth-promotion test, which add elapsed time even when they add little hands-on time.

At low volume, the purchased plate wins on labour almost every time. At high volume, the balance shifts, because the fixed time per batch is spread over more plates. The break-even is not a universal number; it depends on the technician's loaded hourly cost, the price of the prepared plate, the cost of the dehydrated medium and the value of the bench time.

The hidden cost on the in-house side is the release testing. A batch that is poured on Friday and needed on Monday has to be sterility-checked and growth-promoted before it is used, which means the laboratory either holds a buffer stock or accepts that the batch is not available on the day it is made.

Monthly plate use Usual route Reason
Under about 200 plates Buy prepared Release testing and labour dominate
200-600 plates Mixed Buy the routine formats, pour the special ones
Over about 600 plates Pour in-house Fixed batch time spreads across volume
Any volume, unusual formulation Pour in-house No prepared equivalent
Any volume, disk diffusion Buy or verify depth carefully Depth tolerance is tight

What quality checks does each route need before use?

For a bought plate, the laboratory's acceptance check is a lot verification: confirm the expiry, the storage history, the appearance, and the growth promotion or a documented supplier certificate. CLSI M22 describes the quality control of commercially prepared media; the laboratory's own procedure should say which checks it repeats and which it accepts from the certificate.

For an in-house plate, every batch needs a sterility check, a pH check where the medium is pH-sensitive, a depth check for methods that depend on it, and a growth-promotion test with the organisms the method requires. ISO 11133 is the reference for the performance testing, and the records should identify the batch, the medium, the lot of dehydrated powder and the organisms used.

The depth check is the one most often skipped and the one most likely to matter. A plate that is visibly thicker at one edge will give a different zone diameter at that edge in a disk diffusion test, which is why CLSI M02 works from a depth specification rather than a volume alone.

Check Bought prepared Poured in-house Record
Appearance and expiry Every plate or lot Every batch Lot, date, pass
Sterility Supplier plus acceptance Every batch Incubation conditions, result
pH Supplier certificate Every batch where relevant Measured value
Depth Verify on receipt where critical Every batch Volume and plate size
Growth promotion Supplier certificate or laboratory check Every batch Organisms, incubations, result

How should plates be stored and handled?

Prepared plates are stored at 2-8 °C and must not be frozen. Freezing damages the gel structure and produces plates that weep on thawing. The plates should be kept in the original sleeve or bag, inverted, and brought to room temperature before use so that condensation does not drip onto the agar surface.

In-house plates follow the same storage rules with a shorter shelf life. The laboratory sets the shelf life from its own validation, not from the dehydrated medium's shelf life. A plate that has dried, cracked or pulled away from the wall is not usable, whatever the date says.

Handling matters as much as storage. A plate that is opened on the bench and left open while the technologist sets up is a plate that collects airborne contamination. The lid is lifted, not removed, and the plate is returned to the stack as soon as the inoculation is done.

Clear graduated specimen container with a white screw cap, marked in ounces and millilitres

What goes wrong most often with in-house plates?

The common failures are condensation, cracking, contamination and depth. Condensation comes from pouring too warm or stacking too soon; cracking comes from cooling too fast or from a medium that is too dry; contamination comes from pouring in a draught or from an inadequate sterility check; depth comes from eyeballing the volume instead of measuring it.

Each failure has a process fix. Pour at the temperature the medium manufacturer specifies, let the plates set and dry as the procedure requires, stack only when the agar is solid, and measure the volume with a graduated cylinder or a dispensing pump rather than by eye. The sterility check is not optional because contamination can be invisible at the moment of pouring.

The release decision is the control point. A batch that fails the sterility or growth-promotion check is discarded, and the reason is recorded. A batch that passes is released with the date, the medium, the lot and the operator, because that record is what allows the laboratory to trace a problem back to a batch rather than to a shift.

Pair of blue nitrile examination gloves on a white background

A media bench reorders containers and bench consumables together. Order through the wholesale programme for case pricing and an account, or become a distributor for resale. The sterile 15 mL centrifuge tubes sits in the same catalogue. Consumables for this line are listed under the department page.

Sources

  1. ISO 11133:2014, microbiology of food, animal feeding stuffs and water, preparation, production, storage and performance testing of culture media
  2. CLSI M22, quality control for commercially prepared microbiological culture media
  3. CLSI M02, performance standards for antimicrobial disk susceptibility tests
  4. ISO 15189:2022, medical laboratories, requirements for quality and competence
  5. ISO 13485:2016, medical devices quality management
  6. ISO 14971:2019, application of risk management to medical devices
  7. Public Health Ontario, infection prevention and control
  8. Health Canada, medical devices
  9. Health Canada, establishment licensing
  10. Medical Devices Regulations, SOR/98-282
  11. WHO guidelines on drawing blood
  12. CLSI GP41 companion quick guide, venous specimen collection
  13. CLSI H21, plasma-based coagulation assays
  14. Standards Council of Canada
  15. CSA Group, standards catalogue
  16. Measurement Canada
  17. Canadian Association of Optometrists
  18. Royal College of Dental Surgeons of Ontario, standards and guidelines

Printable media batch release sheet. Every poured batch needs a sterility result, a depth measurement and a growth-promotion result before it is used. Print a media batch release sheet - one page per batch, with the medium, the lot, the plate count and the release signature; it prints with no account and no sign-up.

Log generator. Build a dated media preparation calendar so that the release checks land before the plates are needed. Build a media preparation schedule - the page lays out the preparation dates, the release dates and the expiry dates in one view.

Ask a compliance specialist. Whether a laboratory may accept a supplier's release certificate for a lot, or must repeat growth promotion in-house, depends on the method and the accreditation body. Ask a compliance specialist - written answer specific to your equipment and province, with the regulation or standard it is based on cited.

Related reading

CliniEco Medical supplies eye care, laboratory and dental consumables of the kind described in this article. MDEL #35334. This article is written for laboratory managers and is not legal advice; media release criteria belong to the laboratory's quality management system and to the method it is supporting.

Frequently Asked Questions

Is a bought agar plate ready to use?

It is released by the manufacturer, but the laboratory still verifies the lot: expiry, storage history, appearance and growth promotion or a documented supplier certificate. CLSI M22 describes the quality control of commercially prepared media.

How much agar goes into a 90 mm plate?

About 25 mL gives a depth near 4 mm, which is the working depth for disk diffusion. Thirty millilitres gives about 4.7 mm and changes the depth, which can shift zone diameters.

How long can in-house plates be stored?

The laboratory sets the shelf life from its own validation. In-house plates are normally shorter-lived than purchased plates and must be stored at 2-8 °C without freezing.

What release tests does an in-house batch need?

A sterility check, a pH check where relevant, a depth check and a growth-promotion test with the organisms the method requires. ISO 11133 is the reference for the performance testing.

Why do plates crack or sweat?

Cracking usually comes from cooling too fast or a medium that is too dry. Sweating comes from pouring too warm or stacking before the agar is fully set. Both are process problems rather than storage problems.

When is pouring in-house worth it?

At high volume, for unusual formulations, or where the method needs a plate that is not commercially available. At low volume the labour and release testing usually cost more than the prepared plate.

Already working with clinics? Become a regional representative.