Quick answer: most Canadian labs order the 100 × 15 mm dish as their working size, with 90 mm and 60 mm formats for specific methods, and they order by case with the vented or non-vented choice fixed per method rather than per convenience. Case counts vary by manufacturer, so confirm units per case before comparing price. Our 100 x 15 mm sterile polystyrene petri dishes ship 320 to a case.
Which sizes matter and what are they used for?
Size is usually set by the method, the incubator rack and the colony-counting workflow, not by preference. The 100 × 15 mm dish offers a large surface for air sampling and general culture; 90 mm is common where automated counters and standard racks are calibrated to it; 60 mm suits small-volume work and contact plates.
| Size | Typical use | Considerations |
|---|---|---|
| 100 × 15 mm | General culture, air sampling | Large surface, fits most racks |
| 90 × 4 mm | Contact plates, surface sampling | Grid options for counting |
| 90 × 15 mm | Routine culture | Compatible with many automated counters |
| 60 × 15 mm | Small-volume work, screening | Lower agar consumption per plate |
Vented or non-vented?
Vented dishes allow gas exchange and reduce condensation, which matters for long incubation and for organisms that need airflow. Non-vented dishes limit moisture loss in dry incubators and reduce cross-contamination risk in crowded incubators. The choice belongs to the method, so a lab running both formats should stock both rather than standardise on one.
How do you compare case counts properly?
Convert to cost per dish before comparing. Cases are described as 500, 480 or 400 depending on manufacturer and sleeve configuration, and a “cheaper” case with fewer dishes is often the more expensive option. Also confirm whether the case contains sleeves of 20 or loose stacks, because sleeve count affects how long an opened case stays usable.
How many dishes are in a case of 100 × 15 mm petri dishes?
A case of the 100 × 15 mm sterile polystyrene dish holds 320 dishes. That is the figure to quote in a requisition, because a supplier who describes the same product as 400 or 480 per case is describing a different sleeve count, and the price per dish only becomes comparable once both numbers are on the page.
| Size | Units per case | What to confirm before ordering |
|---|---|---|
| 100 × 15 mm | 320 dishes | Case quantity as stocked; sleeves inside the case |
| 90 × 15 mm | Set by the supplier and the packaging method — confirm before ordering | Sleeve count and whether the case is 10 per sleeve |
| 90 × 4 mm | Set by the supplier and the packaging method — confirm before ordering | Grid format, since some counts depend on the printed grid |
| 60 × 15 mm | Set by the supplier and the packaging method — confirm before ordering | Height, because more than one height is labelled 60 mm |
Working out the ordering rhythm from 320 per case
A lab using 100 dishes a week goes through one 320-dish case in a little over three weeks, so a reorder point at one week of stock lands at the end of week two. A lab using 250 a week goes through a case in about six working days and should order three or four cases at a time to cover a month. Put the number in the same place as the media order, because plates and agar run out in the same week. Write that reorder point on the shelf label as well as in the ordering file, since the person who notices an empty shelf is rarely the person who owns the spreadsheet.
How should dishes be stored?
Sealed, dry, at room temperature, away from direct light, and rotated so the oldest case is used first. Sterility depends on the packaging remaining intact, so a case that has been opened and left in a humid room should not be carried into a sterile workflow. Write the opening date on the case.
What should be recorded for each lot?
Lot number, size, vented status, quantity and receiving date. When a contamination event occurs, the lot is the first thing to check, and a lab without a lot register ends up discarding stock it did not need to discard. A printable consumable lot register and the log generator cover it.
Labs ordering across sites can consolidate through wholesale and multi-site ordering, and the B2B wholesale collection lists the laboratory lines stocked for institutional buyers. Reselling? become a distributor.
Related reading
- 100 x 15 mm Petri Dishes: Canadian Lab Ordering Checklist
- Vented and Non-Vented Petri Dishes
- Agar Types, Prepared Plates and Storage
Frequently Asked Questions
What is the standard petri dish size in Canadian labs?
100 x 15 mm is the common working size, with 90 mm formats used where counters and racks are calibrated to them.
Vented or non-vented dishes?
Vented for gas exchange and condensation control on long incubation; non-vented to limit moisture loss and cross-contamination. The method decides.
How many dishes are in a case?
It varies by manufacturer and sleeve configuration: 400, 480 or 500 are common. Convert to cost per dish before comparing.
How should unopened cases be stored?
Sealed, dry, at room temperature and away from direct light, rotated oldest first so sterility packaging stays intact.
CliniEco Medical is a licensed medical device establishment (MDEL #35334).