Chemical breakthrough in a nitrile glove is not the same as a hole. Breakthrough happens when a chemical migrates through the intact polymer film at a molecular level. A glove can look perfect, feel dry, and still be passing a solvent through to the skin.
Three test concepts matter, and they are routinely confused: breakthrough time, permeation rate, and degradation. Each answers a different question about the same glove.
What is the difference between breakthrough time and permeation rate?
Where to Buy Nitrile Examination Gloves in Canada
CliniEco Medical supplies examination-grade nitrile gloves to clinics, laboratories, food facilities and care homes across Canada, shipped from Ontario.
| Option | Best for | Order |
|---|---|---|
| 4 mil, blue (100/box) | General examination and short procedures | 4.0 mil nitrile exam gloves, 1,000 per case |
| 6 mil, black (100/box) | Heavy-duty handling, higher puncture risk | 6 mil Black, 100-Pack |
| Case of 10 boxes | Sites going through gloves daily — lowest cost per glove | Wholesale Case, 1,000 Gloves |
| Chemo-grade 4.0 mil | Any handling that may involve cytotoxics | Chemo-Grade, 100-Count |
| Starting a clinic? | Gloves plus spore testing plus packaging in one order | Clinic Starter Bundle |
Ontario and GTA orders ship free over $99; elsewhere in Canada over $199 ($15 flat below). Bulk and standing orders go through a wholesale account. Print a blank sterilization log sheet from our free generator, or book a sterilization compliance review.
Breakthrough time is how long, from first contact, it takes for a chemical to be detected on the inside surface of the glove at a defined detection threshold. Permeation rate is how fast the chemical moves through once it has begun. A short breakthrough time combined with a low permeation rate is still a poor result for a chemical you will handle for an hour, because the clock starts at first contact whether or not the glove is visibly affected.
Why is degradation a separate question?
Degradation is a physical change in the glove material: swelling, softening, hardening, or loss of strength. A glove can resist permeation and still degrade badly, which destroys its mechanical protection and its barrier to microorganisms at the same time. This is why a compatibility chart with a single pass or fail column is less useful than one that separates permeation results from degradation observations.
| Test concept | What it measures | Typical reporting | Practical meaning |
|---|---|---|---|
| Breakthrough time | Time to detection on the inner surface | Minutes, by chemical | How long the glove is usable for that chemical |
| Permeation rate | Mass passing through per area per time | Micrograms per square centimetre per minute | Exposure once breakthrough begins |
| Degradation | Physical change in the film | Rating scale after exposure | Whether the glove still works mechanically |
| Pinhole leak test | Physical defect detection | Acceptable quality level | Manufacturing integrity, not chemistry |
Why does chemistry decide the result?
Nitrile butadiene rubber resists a broad range of solvents because of its acrylonitrile content and cross-linking. Even so, chlorinated solvents, aromatic hydrocarbons and some ketones attack it. Where a nitrile glove performs poorly against a chlorinated solvent, the correct response is usually to change the glove polymer rather than to add a second nitrile layer.
Standardised permeation testing exists precisely so that results are comparable across products rather than dependent on a supplier's own method. In practice, when a clinic is choosing gloves for a specific solvent, the useful steps are: identify the chemical by name and concentration, check the permeation result for that chemical rather than for the chemical family, and then confirm degradation separately.
What should a clinic actually do with this?
Build a short list of the chemicals your team actually handles, with concentrations, and check glove compatibility for those specific items rather than for a category. Keep the highest-risk task separate: a glove that is adequate for general examination and cleaning work may be wholly inadequate for a solvent-based procedure, and the choice should be made per task rather than per department.
For most clinical and care settings, an examination-grade nitrile glove used for examination and general care is the right default, with a heavier-gauge glove reserved for the mechanical-demand tasks. Neither choice overrides the need to know what the chemical is.


Related Reading
- ASTM D6319 explained: what glove certification means
- Nitrile vs latex vs vinyl gloves compared
- Glove collection
Frequently Asked Questions
Is chemical breakthrough the same as a pinhole in a glove?
No. A pinhole is a physical defect in the film that can be detected by a leak test. Breakthrough is molecular migration through an intact film, detected by permeation testing rather than by inspection.
How do I choose a nitrile glove for a solvent I use?
Identify the chemical by name and concentration, then check the permeation result for that specific chemical rather than for a broad solvent category, and check degradation separately. If nitrile performs poorly, a different glove polymer may be the answer.
Does a thicker glove prevent chemical breakthrough?
Thickness changes the timing but not the chemistry. A thicker glove delays breakthrough and improves mechanical durability, but a chemical that permeates the polymer will still get through given enough contact time.
Ordering for a clinic, lab or care home? Wholesale and multi-site ordering covers case pricing and account setup, and the B2B wholesale collection lists the lines stocked for institutional buyers.
Start with a trial: Biological Indicator 5-Pack Trial (free, ships free) for a single sterilizer, or request the Rapid Reader seed trial for multi-site monitoring programs.
CliniEco Medical is a licensed medical device establishment (MDEL #35334).