Gown Fabric Weight: 35, 40 or 45 GSM SMS?

CliniEco Medical isolation gown laid flat, back ties and front panel

Gown Fabric Weight: 35, 40 or 45 GSM SMS?

Why Two Gowns Rated at the Same Level Weigh Different Amounts

Two isolation gowns, both labelled Level 2, both in blue, both sold by the case. One carton says 35 gsm and the other says 45 gsm. The instinct is to assume the heavier one is better and the lighter one is a shortcut.

Neither assumption survives a specification meeting. The two figures measure different things, and a clinic that buys on the number printed in the largest font tends to overpay for the tasks that need less, and under-specify the tasks that need more.

This guide goes through what the gsm figure actually measures, how a three-layer SMS laminate is put together at each weight, and how to write a purchase order that names fabric weight and barrier level together so the two cannot drift apart.

What Does the GSM Number Measure?

Grams per square metre, measured to ISO 9073-1: a conditioned specimen of known area is weighed, and the result is expressed as mass per unit area.

That definition carries two consequences that matter to a buyer. First, gsm is a mass measurement, so it describes how much material is in the sheet and not how the material is arranged. Second, because it is measured on a specimen, the figure belongs to a production lot; a mill that changes its fibre blend can hold gsm constant while changing how the sheet performs.

Related test methods cover the properties gsm does not: ISO 9073-4 measures tear resistance, and ISO 9073-10 characterises lint and particulate shedding in the dry state. A gown specification that lists only gsm has named one property out of several that decide whether the garment survives a shift.

How Is an SMS Gown Built?

Light blue CliniEco SMMS 40 gsm Level 2 isolation gown with cuff and tie detail

SMS stands for spunbond, meltblown, spunbond. Three webs are formed and bonded into a single sheet:

  • The outer spunbond layers carry tensile strength, abrasion resistance and the shape of the garment
  • The middle meltblown layer is made of much finer fibres and does the fluid and particle resistance work
  • The bonding method, usually thermal calender or ultrasonic, decides how the layers stay together after flexing

Because the meltblown web is the barrier, the useful internal number is not total gsm but the meltblown share of it. A 40 gsm laminate with a heavier meltblown component can outperform a 45 gsm laminate with more spunbond. No carton prints that split, which is exactly why the level has to be asked for separately.

What Do 35, 40 and 45 GSM Change in the Hand?

Fabric weight Typical construction How it handles Tasks it suits
:-- :-- :-- :--
35 gsm Lighter spunbond outer layers, thin meltblown core Softer drape, easier to don in a hurry, less resistance to snagging Reception screening, cohorting support staff, low-spatter examination
40 gsm Balanced spunbond and meltblown, common Level 2 pairing Holds shape through a shift, resists a wipe-down, moderate stiffness Examination and procedure rooms, dental hygiene, wound care
45 gsm Heavier outer webs, thicker core, stiffer hand Noticeably warmer, better abrasion resistance, less drape Longer procedures, tasks with irrigation or spray, high-contact care

The gown most examination rooms in Canada settle on sits in the middle of that table: the SMMS 40 gsm Level 2 gowns, which pair a balanced laminate with a test result rather than a weight printed on its own.

The difference staff notice first is warmth. A 45 gsm gown worn for a full morning in a warm treatment room produces complaints that have nothing to do with protection and everything to do with comfort, and uncomfortable staff take gowns off between patients. The difference auditors notice is the case count, because heavier laminate means fewer gowns per carton at the same fold.

Does a Heavier Gown Give a Higher Level?

Blue disposable isolation gown with cuffs and waist ties

No, and this is the sentence worth pinning above a purchasing desk. Level is a test result; gsm is a material property. A supplier can build a 45 gsm gown that reaches Level 1 and a 40 gsm gown that reaches Level 2, and both statements can be true at once.

The reason is that the tests do not weigh the gown. They subject it to a challenge and measure what passes through.

PB70 level Tests that define it What the result means
:-- :-- :--
Level 1 Water impact penetration, 4.5 g or less Minimal fluid contact, brief examination
Level 2 Water impact 1.0 g or less plus hydrostatic pressure 20 cm or more Splash and sustained contact short of a soaked challenge
Level 3 Water impact 1.0 g or less plus hydrostatic pressure 50 cm or more Heavier splash, longer fluid exposure
Level 4 Viral penetration testing to ASTM F1671 Blood-borne pathogen challenge at the material level

For gowns used where blood or body fluids can be projected, the relevant additional test is ISO 16604, which measures resistance of protective clothing materials to penetration by blood-borne pathogens. A clinic that writes "Level 2" on an order and stops there has named a band; a clinic that writes the level plus the material weight plus the test standard has named a product.

How Do You Read a Gown Carton?

Four things on the carton decide whether the delivery matches the order:

  • The level, stated against the standard the supplier tested to
  • The fabric weight, in gsm
  • The case count, in gowns rather than packs
  • The lot, so a problem can be traced to a delivery

Section 21 of the Medical Devices Regulations sets out what the label must carry, including the name of the device, the manufacturer's name and address, the identifier, the contents where they are not obvious, the intended use and directions, any special storage conditions, and the word Sterile where the manufacturer intends a sterile presentation. Symbols follow ISO 15223-1, which is why the single-use mark rather than a sentence is what most cartons show.

CliniEco Medical isolation gown laid flat, back ties and front panel

What the regulations do not do is set a fabric weight. Gsm is a commercial specification agreed between buyer and seller, which means it is only enforceable if it appears on the purchase order.

How Do You Write GSM Into a Purchase Order?

A specification line with four components survives a substitution:

  • Level, named with the standard, for example Level 2 with the test reports held on file
  • Fabric weight, in gsm, with a tolerance band agreed in writing
  • Cuff and closure type, since a knit cuff and a tie-back change how the gown behaves at the wrist
  • Case count and pack format, because case count is what par levels are calculated against

The tolerance band is the part most orders omit. A supplier asked for 40 gsm who delivers a 38 gsm lot has met a specification written without tolerance and breached one written with a 5 percent band. Writing the band costs one sentence and prevents an argument that a clinic cannot win on documents alone.

What Else Changes When the Gown Changes?

Three operational effects follow a fabric change, and all three show up within a month.

Warmth changes wear time. Staff who find a gown hot remove it between patients, which converts a product decision into a compliance decision.

Case count changes storeroom maths. At the same carton volume, a heavier laminate holds fewer gowns, so the par level that worked at 35 gsm runs short at 45 gsm. Our clinic supply and cost planner recalculates boxes per month from patient contacts, which is the number par levels are built from.

Freight changes cost per gown. A pallet of 45 gsm gowns carries fewer units, so a delivered cost comparison between two weights has to be done per gown and not per case.

For clinics standardising across sites, the practical approach is to choose the level per task and the weight per season of use, then hold both constant. The isolation gown range lists material weight and level on each product page, and the gowns most examination rooms settle on are the SMMS 40 gsm Level 2 gowns for procedures and the Level 1 non-woven gowns for low-splash support work. Facilities with a waste-reduction mandate sometimes ask about the PLA biodegradable Level 1 gowns, which trade a narrower discipline for a different end-of-life route.

How Do You Sample Two Weights Before Committing?

Wear both for one shift in the room where the gown is actually used, and record three things: how many gowns each staff member used, whether any tore at the cuff or tie, and whether anyone removed a gown between patients.

A case of each is a small spend against a year of the wrong weight. The full field-trial method, including what to write down and how to compare two candidates against the same task list, is set out in our guide to supply evaluation for clinics.

References

  1. Medical Devices Regulations (SOR/98-282), section 1, interpretation (checked 13 November 2026)
  2. Medical Devices Regulations (SOR/98-282), section 21, label requirements (checked 13 November 2026)
  3. Medical Devices Regulations (SOR/98-282), section 44, establishment licence (checked 13 November 2026)
  4. Medical Devices Regulations (SOR/98-282), section 52, distribution records (checked 13 November 2026)
  5. Medical Devices Regulations (SOR/98-282), section 59, mandatory problem reporting (checked 13 November 2026)
  6. ISO 9073-1:1989, Nonwovens, determination of mass per unit area (checked 13 November 2026)
  7. ISO 9073-4:2021, Nonwovens, determination of tear resistance (checked 13 November 2026)
  8. ISO 9073-10:2003, Nonwovens, lint and other particles in the dry state (checked 13 November 2026)
  9. ISO 16604:2004, Clothing for protection against contact with blood and body fluids, resistance of protective clothing materials to penetration by blood-borne pathogens (checked 13 November 2026)
  10. ISO 15223-1:2021, Medical devices, symbols to be used with information supplied by the manufacturer (checked 13 November 2026)
  11. ISO 13485:2016, Medical devices, quality management systems (checked 13 November 2026)
  12. ISO 10993-1:2025, Biological evaluation of medical devices, evaluation and testing within a risk management process (checked 13 November 2026)
  13. Food and Drugs Act (R.S.C., 1985, c. F-27), consolidated text (checked 13 November 2026)
  14. Health Canada, Medical devices, regulatory overview (checked 13 November 2026)
  15. Public Health Agency of Canada, Routine Practices and Additional Precautions for Preventing the Transmission of Infection in Health Care (checked 13 November 2026)
  16. Public Health Ontario, Routine Practices and Additional Precautions (checked 13 November 2026)
  17. Recalls and safety alerts, searchable database of Canadian product recalls (checked 13 November 2026)

Buying for a facility? Open a wholesale and institutional account for case pricing, purchase-order billing and a named account contact. Reselling? become a distributor.

Writing the specification? The wholesale account desk keeps the material and test detail for each gown line on file, so a purchase order can name the fabric weight and the barrier level in the same line.

Comparing two quotes? The bulk quote desk returns a line-item quote with the case count, the fabric weight and the level stated, which is the version that survives an audit three months later.

Related Reading

Frequently Asked Questions

Does a higher gsm mean a higher barrier level?

No. The barrier level is a test result, and the fabric weight is a material property. A 45 gsm gown can fail a hydrostatic test that a well-built 40 gsm gown passes, because the meltblown layer in the middle of the laminate does more for fluid resistance than the total weight does. Weight tells you how much material is present; the level tells you what the material did under a named test.

What does SMS stand for on a gown carton?

Spunbond, meltblown, spunbond. Three layers bonded into one sheet: two outer spunbond webs that carry strength and abrasion resistance, and a middle meltblown web of fine fibres that does the filtration work. The construction is why SMS gowns feel stiffer than a single-layer spunbond gown at the same weight.

Is 40 gsm the standard for Level 2 gowns?

It is a common commercial pairing rather than a rule. Level 2 is defined by test performance, and suppliers reach those results with different laminate weights and different meltblown basis weights. Plenty of Level 2 gowns are 40 gsm; some are 42 or 45 gsm, and some lighter constructions reach Level 1 only. Ask for the level and the report, then use the gsm figure to compare hand feel and durability between candidates that already meet the level you need.

How is gsm actually measured?

Mass per unit area, per ISO 9073-1: a conditioned specimen of known area is weighed and the result is expressed in grams per square metre. Because it is a mass measurement, it says nothing about how the layers are distributed. Two 40 gsm laminates can differ in meltblown share, and that difference is invisible on the carton.

What does AAMI PB70 Level 2 require?

Under the PB70 hierarchy, Level 1 requires a water impact penetration result of 4.5 grams or less on the AATCC 42 test. Levels 2 and 3 tighten that to 1.0 gram or less and add AATCC 127 hydrostatic pressure thresholds of 20 cm and 50 cm respectively. Level 4 adds viral penetration testing to ASTM F1671. The numbers are worth writing into a specification because they are measurable and comparable.

Why do some gown cartons list grams and others list ounces?

Because different export markets use different conventions. A yard-based ounce figure is common on material datasheets from some mills, while metric gsm is standard on Canadian and European cartons. Convert rather than compare across systems; a figure quoted in ounces per square yard is not the same number as a gsm figure, and mixing them produces a specification nobody can check.

Does fabric weight affect case size and freight?

Yes, and that is often the real commercial difference. A heavier laminate packs fewer gowns into the same carton volume at the same fold, so the case count and the pallet count change. A clinic that switches from 35 to 45 gsm without recalculating par levels will order the same case count and find the storeroom empties faster.

Are these gowns single use?

The gowns stocked for examination and resident care in Canadian clinics are single-use items, labelled with the single-use symbol under ISO 15223-1. Reuse decisions belong to facility policy and to the manufacturer's stated intended use, not to how intact the gown looks after a shift.

Last updated: November 2026. CliniEco Medical is a licensed medical device establishment (MDEL #35334).

Already working with clinics? Become a regional representative.