How are foot impression materials handled in Canadian podiatry clinics?
A podiatrist finishes a slipper cast at 9:40 and the next patient is already in the chair. The plaster bandage goes into a bag, the mixing bowl goes to the sink, and the set cast waits on the bench for the courier at noon. Nothing there is complicated, and the fit complaints that arrive two weeks later are almost always handling problems, not material ones.
Three materials cover nearly every orthotic prescription in Canada: plaster bandage for a weight-bearing slipper cast, addition-cure silicone for a non-weight-bearing mould, and closed-cell foam for an accommodative insole. Each fails in its own way, so each one earns its own line on the chart. The mix happens on a paper-covered surface with nitrile examination gloves, 3.5 mil, 1,000 per case, not on a bare bench that then has to be scraped.
How are foot impression materials handled in a Canadian podiatry clinic?
Four steps repeat in every treatment room: confirm the material is in date and still sealed, mix to the maker's ratio and working time, record the position the foot was held in, then release the set impression to the lab with the prescription attached. Storage is where clinics drift: plaster bandage pulls moisture from a humid room and sets unevenly, and silicone opened in spring cures soft. Writing the opening date on the container makes that visible before a patient feels it.

Which material suits which impression?
| Material | Sets by | Storage watch | Chart note |
|---|---|---|---|
| Plaster bandage | crystal set, minutes | sealed and dry; a damp roll sets loose | foot position, cast type |
| Addition-cure silicone | chemical set, short working time | base and catalyst sealed, in date | lot, mix ratio, pour date |
| Closed-cell foam | compression, immediate | flat storage, no heat | box size, trim line |
| Impression tray | n/a | cleaned after every use | reprocessing cycle |
Does a foot impression create a medical device record?

Health Canada's Medical Devices Regulations treat a device made for a named patient on a written prescription as a custom-made device, putting the manufacturing record on the lab. The clinic still owns the input: which foot, position, lot, who took it and when it left. When a shell comes back tight, that line separates a casting error from a material error.
What has to be cleaned before the next patient?
Set material on a tray edge is the usual reason a disinfection step fails, so scrape and rinse before any wipe. Reusable impression trays and mixing bowls then follow the maker's validated processing information and provincial reprocessing guidance, and CSA Z314:23 covers them as reusable equipment. Surfaces get a fresh length of perforated exam table paper, 21 inch so the next mix starts clean, and dry disposable washcloths take the plaster off hands and feet before it reaches a tap.
What goes wrong between the cast and the lab?
Silicone and plaster both keep, but not in a hot car or an unvented storeroom. A bag with condensation inside pours with surface defects, and a cast that has been compressed under a box of stock is a re-take. Send it flat, and send it in the week it was taken.
Running a foot care or physiotherapy practice? See our podiatry and physiotherapy clinic supplies.
Ordering for a clinic, lab or care home? Wholesale and multi-site ordering covers case pricing and account setup, and the B2B wholesale collection lists the lines stocked for institutional buyers. Reselling? become a distributor.
References
- Public Health Ontario — provincial guidance on cleaning, disinfection and sterilization of medical equipment in health care settings (checked 8 November 2026)
- ISO 17664-1:2021, Processing of health care products — information to be provided by the medical device manufacturer (checked 8 November 2026)
Printable companion: the free clinic log and checklist library includes an impression and tray reprocessing sheet with material lot, mix time and initials already ruled.
Turning appointment volume into consumable volume? The clinic supply and cost planner turns a week of casting appointments into rolls of table paper, boxes of gloves and canisters of material per quarter.
Related Reading
- What is the accepted cleaning routine for podiatry drills and suction in Canadian foot clinics?
- Setting up a podiatry clinic's sterilization workflow in Canada
- Podiatry Clinic Supplies in Canada: What a Treatment Room Stocks
Frequently Asked Questions
Do Canadian foot clinics use alginate for orthotic impressions?
Rarely. Alginate is a dental material: it tears off a loaded foot and shrinks as it dries. Plaster bandage, addition-cure silicone and closed-cell foam cover almost every orthotic prescription.
How long can a set foot impression wait before it is poured?
A plaster slipper cast is poured or scanned within a few days, silicone inside the working window the maker prints. A cast that spent an afternoon in a hot vehicle is worth re-taking.
Does an impression have to be disinfected before it leaves for the lab?
Clean and disinfected to the level the material maker specifies, then bagged on its own. Visible blood or fungal debris moves it up a level, and the lab should be told.
What record does a foot clinic keep for impression material?
Opening date, lot, expiry, which foot, the position the foot was held in, and the date the impression left. That line explains most fit complaints that arrive weeks later.
Last updated: October 2026. CliniEco Medical is a licensed medical device establishment (MDEL #35334).