Use the printable autoclave log sheet below to track every autoclave cycle in your dental or medical clinic. A sterilization log is the record an inspector, public health officer, or liability investigator asks for first — and the difference between a well-run sterilization program and one that looks unmanaged on paper is often simply whether the entries exist.
This page gives you the log itself, explains what each column means, and shows how the log fits into the complete monitoring picture: chemical indicators on every pack, biological indicators (spore tests) on every day the sterilizer is used, and mechanical checks on every cycle. Print the table, make copies, and keep one binder per sterilizer.
The sheet is print-ready. One page, letter landscape, 20 cycle rows, 14 fields — including the BI lot number and BI result columns that most paper logs leave out.
Download the printable log sheet (PDF)
No sign-up and no email required. Prefer a screen? Fill the same 14 fields in the browser and export CSV or print. The download button is repeated beside the table further down the page.
What the log sheet actually requires. Each column of the record maps to one item below — this is the set that makes a cycle provable.
Closing the loop also takes indicator tape and a constant-heat pouch sealer — both listed with the packaging.
Looking for the supplies in this guide? We stock them in Canada and ship from Toronto.
Autoclave monitoring & spore testing → · Wholesale & clinic accounts · Free sterilization log tool · Ask a compliance specialist
Why do sterilization logs matter?
Products referenced in this guide
- 24-Hour Biological Indicators — 25-Pack — $69.99
- 24-Hour Biological Indicators — 50-Pack — $109.99
- 24-Hour Biological Indicators — 100-Pack — $189.00
- 3-Hour Biological Indicators — 50-Pack — $249.99
- 20-Minute Rapid Readout Biological Indicators — 50-Pack — $289.99
- 1-Hour Rapid Readout Biological Indicators — 50-Pack — $269.99
- Autoclave Indicator Tape — 3-Roll Set — $159.92
- Class 5 Chemical Integrators — 200 per pack — $159.92
Sterilization is a process, not a single event. A machine can display "cycle complete" while a packed chamber never reached temperature in the dense zone, and that failure is invisible unless something is recorded and checked against the expected parameters. Logs exist for three reasons:
Inspection readiness. Provincial dental regulators, including the Royal College of Dental Surgeons of Ontario, review sterilization documentation during quality assurance visits. A complete log demonstrates that monitoring was performed consistently — not reconstructed the night before the visit.
Outbreak and incident investigation. If a patient develops a post-treatment infection or a positive spore test surfaces, the log is how the clinic can reconstruct which instruments were in which cycle, whether the parameters were met, and what corrective action was taken. Without records, every instrument processed in the suspect period is unverifiable.
Continuous improvement. A log makes patterns visible. Cycles that consistently run at the edge of the temperature range, or a sterilizer that fails its spore test twice in a quarter, are signals that the unit needs maintenance before a full failure occurs.
The CDC Guidelines for Infection Control in Dental Health-Care Settings and the 2016 Summary of Infection Prevention Practices in Dental Settings both describe monitoring of sterilization cycles and the importance of documenting results. The CSA Group's Z314 series on device reprocessing carries the same expectation in the Canadian context.
What a Compliant Sterilization Log Records
There is no single mandatory national template, but provincial regulators and the technical literature converge on the same fields. A compliant entry captures:
- Date and time of the cycle.
- Sterilizer identification — unit number or name, if the clinic has more than one.
- Cycle type — wrapped, unwrapped, liquid, or implant cycle, and the selected parameters (temperature, time, pressure).
- Load contents — a summary of what was processed (e.g., "20 dental hand instruments, 4 surgical kits").
- Chemical indicator results — external indicator (tape) and internal indicator (pouch) pass/fail per pack.
- Biological indicator result — spore test lot number, incubator temperature, and pass/fail, when a BI was included.
- Mechanical readings — recorded temperature and pressure from the sterilizer display or chart recorder.
- Operator initials — who loaded, ran, and released the load.
- Corrective actions — anything unusual, plus the follow-up taken.
Fill in the entry at the time the cycle runs, not at the end of the week. Retroactive entries are a credibility problem during any investigation.
The Printable Autoclave Sterilization Log Sheet
Download the PDF below and print a stack, or copy the table right on this page. Keep one binder per sterilizer; each row is one cycle.
Download the printable log sheet (PDF) — the same 14-field sheet on one page. No sign-up, no email required.
Download the PDF log sheet1 page · letter, landscape · 20 cycle rows · 14 fields incl. BI lot #
| Date | Time | Sterilizer # | Cycle type | Temp (°C) | Time (min) | Pressure | Load contents | Chem. indicator (CliniEco tape) | Chem. indicator (pouch) | BI lot # | BI result | Operator | Notes / corrective action |
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
A faster option than printing this table
Paper works, but two columns on this sheet are where most clinics fall behind: the "BI lot #" and "BI result" columns. If those sit empty, the log shows monitoring was not performed. Two free resources close that gap, plus the consumable that fills those columns:
- Free sterilization log generator — the same field set, filled in on screen and exported to CSV or printed. No account, no sign-up.
- Sterilization compliance self-check — maps your setting's regulatory requirements to the records you are expected to keep.
- A box of 25 24-hour biological indicators — the consumable that fills the "BI lot #" column, starting this week.
How many biological indicators does the "BI lot #" column need? Under the Ontario requirement, one indicator per sterilizer on every day it is used, and one for each type of cycle. A single sterilizer running one cycle type five days a week uses about 260 per year. At the 100-pack rate that is roughly CA $1.89 per test; at the 25-pack rate, CA $2.80 per test. The 25-pack is the usual starting size for a single-sterilizer clinic.
Tip: print the header row on every page by setting the table rows to repeat, or add the header manually to photocopies.
What is a biological indicator log sheet?
A sterilization log records what the sterilizer did. A biological indicator log records the spore test that shows the cycle actually worked. Most clinics keep both in one binder — cycle rows down the page, spore tests either as their own lines or as the two BI columns of the same row.
The two labels are used almost interchangeably, which is why this page answers for both. The distinction that matters at the bench is granularity, not vocabulary: a cycle log carries one line per cycle and a spore test log carries one line per test. Where a practice runs one test per sterilizer per day, those coincide and this 14-field sheet is enough. Where several cycle types run in a day, the tests multiply and a separate spore-test page is easier to audit than a widening cycle row.
Either layout is defensible if the entry carries six things:
- Date of the test, and the sterilizer it belongs to.
- BI lot number — the traceability link back to the batch the manufacturer released.
- Incubation start and read time, so the endpoint can be shown to be the labelled one.
- Incubator identification and the temperature observed, not just the set point.
- The control result from the same lot — a negative without a control proves nothing.
- The result, how it was read, and the action taken if it was positive.
With those six on the sheet, a reviewer can walk from any load to its spore test and back. Without one of them, the record answers whether the test was run but not whether it was valid — and validity is the question an inspection is actually built to test.
How many entries do you need — per day, per sterilizer, per cycle type?
Granularity is where clinics get this wrong. Three authorities answer the frequency question in three different ways, and only one of them is a per-day rule:
| Authority | What it asks for | Where it applies | How it loads onto the log |
|---|---|---|---|
| RCDSO infection prevention and control standard | One biological indicator per sterilizer on each day the sterilizer is used, and for each type of cycle run that day | Dental practice in Ontario | One BI row per sterilizer, per cycle type, per day of use |
| CDC guideline and ANSI/AAMI ST79 | At least weekly, plus every load containing implants | US practice, used in Canada as a reference baseline | A weekly minimum row per sterilizer |
| CSA Z314 series (CAN/CSA-Z314:2023) | No fixed frequency — a monitoring programme with records, corrective action and recall traceability | Reprocessing in Canada generally | Your procedure sets the frequency; the log has to match it |
| FLTCA and O. Reg. 246/22 | Infection prevention and control duties for long-term care homes, not a sterilization test frequency | Ontario long-term care | Frequency is inherited from the home's own programme |
Worked example, because this is where purchase quantities go wrong. A dental practice with one autoclave runs a gravity cycle at 9 a.m. and a vacuum-assisted cycle at 2 p.m., five days a week. Read as an Ontario dental requirement, that is two tests per day, ten per week, about 500 a year — not one per day. The same practice on the weekly baseline runs 52 tests a year. Same sterilizer, a tenfold difference in consumable.
Two consequences for the sheet. Plan for the cycle-type split before the first test, because a gravity-only practice and a mixed practice need different pack sizes: at two tests a day a 25-pack covers twelve or thirteen test days, while a 100-pack covers roughly ten weeks. And write the frequency into the procedure, then log it as performed — a binder showing 52 tests a year inside a practice that runs two cycle types daily is the most legible gap an inspection can find, because the pattern is in the record itself.
How long do sterilization logs have to be kept in Canada?
There is no single national retention figure, and this is one of the most common places where a clinic adopts a neighbouring jurisdiction's number. What applies depends on the province and the setting:
| Jurisdiction / setting | Retention for sterilization and monitoring records | Source |
|---|---|---|
| Ontario — dental | At least 10 years from the date of the last entry | RCDSO IPAC standard, log book requirement |
| Ontario — dental hygiene | 10 years, under the college's records regulation | CDHO IPAC guidelines |
| Quebec — dental | At least 5 years after the last entry in the record | ODQ record-keeping guide |
| British Columbia — dental | No separate figure for reprocessing records; the general dental record period applies (16 years for records last entered on or after 1 June 2013) | CDSBC recordkeeping guidelines |
| Alberta — clinic | No fixed number; records kept per clinic policy and the legislation that applies to the clinic | CPSA medical device reprocessing standards, section 11.5 |
| Ontario — long-term care | The regulation sets infection prevention and control duties, not a sterilization retention number | Fixing Long-Term Care Act, 2021 and O. Reg. 246/22 |
Because most of those clocks run from the last entry rather than the first, retention is easier to satisfy with one binder per sterilizer per year than with a single continuous log. At the 500-test year described above and 20 rows per printed sheet, a decade of records is a known quantity — about 25 sheets a year — so the tenth year is still retrievable without hunting through storage.
The practical warning: do not apply the 10-year dental figure to a Quebec practice, or the 5-year Quebec figure to an Ontario one. Retention is one of the few monitoring requirements that a practice can be marked down for purely on paper, with no clinical failing involved.
Logs are only half of the inspection picture — how the practice handles the waste stream itself is how to dispose of medical waste in Ontario, which covers segregation, storage limits and carrier requirements.
What does an inspector ask for first?
Whether the visit is a provincial dental inspection, a public health unit review or an accreditation audit, the sequence is remarkably stable:
- The log itself — opened at a recent date chosen by the reviewer, not at a date prepared in advance.
- The spore test result for that day, with its lot number and the control from the same lot.
- The incubation conditions — set point, the temperature actually observed, and the calibration or verification record behind the instrument.
- The corrective action for any positive, invalid or missed test, and which loads it affected.
- An older volume, if retention is in scope: one random past year, to see whether recording was continuous rather than assembled.
Four things break the answer even when the tests were genuinely run. Blank BI columns on days when monitoring happened and was written down somewhere else. A control result that never gets recorded, leaving a negative with no proof it was valid. Entries in one pen or one block of the same handwriting, which reads as retroactive filling — the fastest way to lose credibility in an investigation. And a log for only one of two sterilizers, which is common in practices that added a second unit and never added a second binder.
The last one is the easiest to fix on the sheet itself: the printed sheet has a sterilizer column precisely so a clinic with two units can prove from the binder alone which unit was tested and when. That is why the field set matters more than the format — paper or digital, the column has to exist.
How to Use the Log
Set a simple routine so the log becomes automatic:
- Keep the binder in the sterilization room, next to the autoclave — not in the office.
- Complete each entry at cycle end, while the display readings are still in front of you.
- Record chemical indicator results per pack. For the log, note the number of packs and whether all internal indicators changed correctly.
- Log the daily spore test with the BI lot number, and update the result the next day after incubation.
- Add a corrective action note for any abnormal reading — and follow through.
Digital vs. Paper Autoclave Log Sheets
Clinics ask whether a printed autoclave log sheet is still the right approach, or whether a spreadsheet or app is better. Both work; the choice depends on your team and your risk profile.
Paper advantages. A paper binder is simple, visible, and tamper-evident. Entries are made by hand at the time of the cycle, and any alteration is obvious. It works during power outages, requires no training, and costs nothing to run. For a one- or two-autoclave clinic, paper is usually the lower-friction option.
Digital advantages. A spreadsheet or compliance app can flag missed spore tests, auto-calculate date ranges, and store sterilizer maintenance records in the same file. Digital logs make monthly review faster and allow you to export a clean report for an inspection. The trade-offs are the risk of silent data loss (no backup, laptop failure), the need for staff discipline to open the file at cycle end, and the question of whether the file was edited after the fact.
If you go digital, keep the same discipline as paper: make the entry at cycle end, use a locked or audit-trail format, back up regularly, and keep a paper or PDF archive of completed periods. Some clinics use both — paper at the autoclave during the day, transcribed or scanned into digital storage at week's end. What regulators care about is not the medium; it is whether the record exists, is complete, and was made in real time.
Monthly Log Review Checklist
A log that is filled in but never reviewed has half its value. Once a month, take fifteen minutes to scan the binder for:
- Missed entries or blank fields. Any cycle without an operator initial, or a use day without a spore test, should be explained.
- Marginal readings. Cycles that ran near the low end of the temperature range on the sterilizer display deserve a maintenance check.
- Chemical indicator failures. If any pack's internal indicator did not change, that cycle's packs should be reprocessed and the sterilizer verified.
- Expiry of supplies. Check the dates on pouches, rolls, tape, and biological indicators that are in active use.
- Training gaps. If a new hire's initials start appearing with frequent blank fields, schedule a refresher on the log routine.
Record the review itself — a dated signature on the last page of the month is enough. That signature is the difference between a binder of forms and a managed quality assurance program.
What an Inspector Looks For in the Log
When a public health officer or provincial regulator reviews your sterilization records, they are not checking whether your handwriting is neat. They are looking for evidence of a functioning system:
- Continuity. Entries for every working day, including the days the clinic was busy and short-staffed. Gaps without explanation are a red flag.
- Spore tests on every use day. A biological indicator entry for each sterilizer on every day it is used, and for each type of cycle used that day, with the result recorded the following day. The CDC's disinfection and sterilization guideline sets a weekly baseline for the United States, while the RCDSO requirement in Ontario is a biological indicator on each day the sterilizer is used.
- Corrective actions. When something went wrong — a failed indicator, an unusual reading — did the clinic write down what happened and what was done about it? A log with no notes at all can look like no one was paying attention.
- Consistency between records. The cycle parameters on the log should match the sterilizer's own printouts, and the number of packs processed should roughly match the pouch purchases in your supply records.
None of these require special software. They require the habit of completing the entry at cycle end, and a monthly review that catches small drift before it becomes a finding.
Sterilization Monitoring Beyond the Log
The log records the results; the monitoring products produce them. A complete program uses three complementary layers, and the log is where they all come together:
- Chemical indicators on every pack. Autoclave indicator tape on the outside of every wrapped pack confirms exposure to steam, and a Class 4 indicator inside the pouch confirms temperature and time. The CDC's disinfection and sterilization guideline describes chemical indicators as one of the three required monitoring components.
- Biological indicators every use day. A 24-hour biological indicator (spore test) proves the sterilizer actually killed Geobacillus stearothermophilus spores, per ISO 11138-3. Run it for each sterilizer on every day it is used, record the lot number, and log the result after incubation.
- Mechanical and cycle records. Temperature, pressure, and time readings from the sterilizer display are entered on the log; the sterilizer's own cycle printouts are filed alongside.
Class 4 sterilization pouches with dual indicators close the chain: the internal indicator on each pouch is the pack-level chemical check that tape alone cannot provide. CliniEco Medical's sterilization monitoring collection supplies all three layers from one licensed source.
FAQ: Autoclave Sterilization Logs
What should a sterilization log include?
A complete entry records the date and time, sterilizer identification, cycle type and parameters, load contents, chemical indicator results, biological indicator lot and result, mechanical readings, and the operator's initials. Add notes for any corrective action.
How long do I need to keep sterilization records?
Follow your provincial regulator. Ontario's RCDSO and most provincial bodies expect records to be retained for several years so past cycles can be reconstructed. When in doubt, keep them longer rather than shorter.
Can I keep a digital sterilization log instead of paper?
Yes. Digital logs are acceptable as long as entries are made at the time of the cycle, cannot be easily altered without trace, and are backed up. Many clinics use a paper binder because it is simple and tamper-evident.
What does the biological indicator result column mean?
The BI column records the spore test lot number and the result after incubation — pass (no growth) or fail (growth). A fail entry must include the corrective action taken, including recall and reprocessing of the load.
Do I need a separate log for each autoclave?
Yes. Each sterilizer should have its own log so cycles, spore test results, and maintenance history are traceable to the specific unit.
How often should the log be reviewed?
Review it when you run the spore test, and formally once a month — check for skipped entries, incomplete parameters, and any trend toward marginal readings. This review is often what catches a problem before an inspection.
Is autoclave tape a chemical indicator that belongs in the log?
Yes. Tape is a Class 1 external chemical indicator. Record its pass/fail on the log for each cycle; it shows the pack went through the process, while the pouch's internal indicator verifies conditions inside the pack.
What happens if the log shows a missed spore test?
Run the spore test as soon as possible and note the gap in the log. If you discover the gap while preparing for an inspection, be honest: retroactively filling in results is worse than documenting the correction.
What has to be on every sterilized package label?
A traceable package label carries the date the load was processed, the sterilizer identifier, and the cycle or load number; most Canadian clinic procedures also record the operator. If the label has no date and no load number, the pack cannot be tied back to the cycle that processed it — and that is the first thing an inspector tests.
What must a sterilization load log contain?
One row per cycle: the date and time, the sterilizer identifier, cycle type and parameters (temperature, pressure or time as your sterilizer records them), the load contents, the chemical indicator result, the biological indicator lot and result where one was run for that cycle type, and the operator. Load contents matter — a passing indicator with no record of what was inside the load cannot be reviewed later.
A blank log is a starting point; knowing which fields matter is the real work. The free, sector-specific self-check covers the records and checks an inspector is most likely to look for; it takes about two minutes, prints out, and needs no sign-up.
Related reading: browse the sterilization compliance hub for more spore-testing resources, or generate a free printable sterilization log sheet in your browser and print it — no account, no email.
Related: Never re-order sterilization supplies again — monthly plan from $69/month.
read the foundational SAL explainer before choosing your monitoring products.
References
- Royal College of Dental Surgeons of Ontario. Infection Prevention and Control standard — log book retention requirement. https://www.rcdso.org/en-ca/standards-guidelines-resources/standards-guidelines-advisories/infection-prevention-and-control
- College of Dental Hygienists of Ontario. Infection Prevention and Control Guidelines and Records Regulation (cdho.org).
- Ordre des dentistes du Quebec. Guide d'exercice sur la tenue de dossiers, 2024 (odq.qc.ca).
- College of Dental Surgeons of British Columbia. Dental Recordkeeping Guidelines (cdsbc.org).
- College of Physicians and Surgeons of Alberta. Medical Device Reprocessing Standards, 2022 — section 11.5. https://cpsa.ca/
- Ontario. Fixing Long-Term Care Act, 2021 and O. Reg. 246/22, section 102. https://www.ontario.ca/laws/regulation/r22246
- CDC. Guidelines for Infection Control in Dental Health-Care Settings, 2003 (MMWR RR-17). https://www.cdc.gov/mmwr/preview/mmwrhtml/rr5217a1.htm
- CDC. Summary of Infection Prevention Practices in Dental Settings, 2016. https://www.cdc.gov/oralhealth/infectioncontrol/index.html
- CDC. Guideline for Disinfection and Sterilization in Healthcare Facilities, 2008. https://www.cdc.gov/infectioncontrol/guidelines/disinfection/
- ISO 11140-1 — Chemical indicators for sterilization. https://www.iso.org/standard/71881.html
- ISO 11138-1 — Biological indicators for sterilization. https://www.iso.org/standard/66448.html
- ISO 11138-3 — Biological indicators for moist heat sterilization. https://www.iso.org/standard/67353.html
- ISO 11607-1 — Packaging for terminally sterilized medical devices. https://www.iso.org/standard/70719.html
- CSA Group. Z314 series — Reprocessing of medical devices in Canada. https://www.csagroup.org/
- AAMI ST79 — Comprehensive guide to steam sterilization and sterility assurance. https://www.aami.org/
- Health Canada. Medical devices (regulation overview). https://www.canada.ca/en/health-canada/services/drugs-health-products/medical-devices.html
- Health Canada. Medical device establishment licences (GUI-0064). https://www.canada.ca/en/health-canada/services/drugs-health-products/medical-devices/licences.html
- PHAC. Routine Practices and Additional Precautions. https://www.canada.ca/en/public-health/services/infection-prevention-control-policies/routine-practices-additional-precautions.html
- Royal College of Dental Surgeons of Ontario (RCDSO) — Standards and quality assurance. https://www.rcdso.org/
- Canadian Dental Association (CDA) — Position statements. https://www.cda-adc.ca/
- Journal of Hospital Infection — Sterilization and disinfection research. https://www.sciencedirect.com/journal/journal-of-hospital-infection
- American Journal of Infection Control — Infection prevention evidence. https://www.sciencedirect.com/journal/american-journal-of-infection-control
CliniEco Medical is a licensed medical device establishment (MDEL #35334). This log template is a general reference; confirm requirements with your provincial regulator and sterilizer manufacturer.
Stock the Monitoring Products Behind the Log
CliniEco Medical supplies Class 4 sterilization pouches, autoclave indicator tape, sterilization rolls, and 24-hour self-contained biological indicators for Canadian dental and medical clinics. For bulk pricing or a facility quote, contact us at clinieco.ca/pages/contact — a real person responds within one business day.
Monitoring your sterilizer? Pick the BI format that matches your workflow.
Ontario dental offices must run a biological indicator every day the sterilizer is used (RCDSO). Choose the readout speed that fits your schedule:
- 24-hour self-contained BIs — 25, 50 and 100-count packs for daily monitoring
- 1-, 3- and 20-minute rapid-readout BIs — same-day release when you cannot wait overnight
- 4-well fluorescence reader — incubates and reads rapid-readout BIs in one bench instrument
Shop 24-hour biological indicators Shop the 24-hour readout BI 50-pack
CliniEco Medical · Health Canada MDEL #35334 · Request a wholesale quote
Where to Buy Biological Indicators in Canada
CliniEco Medical supplies these from Ontario with published CAD pricing (MDEL #35334) — no quote required, and each pack ships with the lot number printed on it so your monitoring record stays traceable. CliniEco Medical (Health Canada MDEL #35334) is based in Toronto and supplies CliniEco Sterilization Indicator Tape, Class 4 pouches and sterilization rolls to dental and medical clinics across Canada.
| Item | Pack / format | Price (CAD) | Cost per test | Order |
|---|---|---|---|---|
| 24-hour self-contained BI | 25-pack | $69.99 | $2.80 | 24-hour self-contained biological indicator, 25-pack |
| 24-hour self-contained BI | 50-pack | $109.99 | $2.20 | 24-hour self-contained biological indicator, 50-pack |
| 24-hour self-contained BI | 100-pack | $189.00 | $1.89 | 24-hour self-contained biological indicator, 100-pack |
| 3-hour fluorescence rapid BI | 50-pack | $249.99 | $5.00 | 3-hour fluorescence biological indicators, 50-pack |
| 4-well fluorescence reader | unit | $1,499.00 | — | 4-well fluorescence biological indicator reader |
| 24-hour dry-block incubator | 24 wells | $379.00 | — | 24-hour biological indicator incubator, 24-well dry block |
Which sterilizers and readers these fit: every vial in the table is a self-contained steam indicator for 121 °C gravity-displacement and 132 °C vacuum-assisted (pre-vacuum) cycles; the 24-hour format incubates at 55–60 °C in either dry-block unit, and the 3-hour fluorescence format has to be read in a fluorescence reader. Ethylene oxide, dry-heat and hydrogen-peroxide sterilizers need a different indicator biology and sit outside this table — check the cycle type printed on the unit before ordering, because a gravity-only 121 °C chamber cannot use an indicator validated for 132 °C alone.
How many packs to hold: sterilizers × test days × cycle types = vials per week. One sterilizer tested on every day it is used, five working days a week, runs 5 vials a week, so the 25-pack covers about five weeks and the 100-pack about four months; two sterilizers on that schedule need 10 vials a week, which makes the 50-pack the five-week size and the 100-pack the ten-week size. Add one vial for every extra cycle type run on the same day, and keep a spare pack for the repeat tests that follow a positive result.
Stock and shipping: every item in the table is held in stock in Toronto and ships from Ontario, with the lot number printed on each indicator pack so the entry in your monitoring log can be traced back to the batch. We do not quote a delivery date at checkout.
Round Out Your Sterilization Setup
A biological indicator is one link in the chain — these are the pieces it works with:
- Class 5 chemical integrators — 100-pack — the in-pack check that pairs with your biological indicator
- Sterilization roll — 50 m pre-cut sheets for larger instruments
- Constant-heat pouch sealer — 200 °C, 12 mm seal — for consistent pouch closures
Not sure which format your sterilizer needs? Generate a free sterilization log sheet first — it maps your cycles and tells you the pack size that fits. Questions about your setup? Ask a Compliance Specialist.
A note from Alina
I answer compliance questions from Canadian clinics every week — the same five come up over and over, so I started writing them down.
If these help, subscribe and I'll send the next one. If they don't, no hard feelings — but tell me what you actually need.
One email per new guide. One click to leave. We never share your address.






