Both a Class 5 integrator and a Class 6 emulating indicator are placed inside a pack or inside a process challenge device, and both are read after the cycle. The difference is what each one is designed to represent, and that difference decides which one belongs in your policy.
ISO 11140-1 defines the chemical indicator classes. Class 5 is a integrating indicator intended to react to all critical variables of the sterilisation process. Class 6 is an emulating indicator, designed to react to the critical variables at the values specified for a particular sterilisation cycle.
Buying chemical indicators? Distributed in Canada by CliniEco Medical, Toronto.
CliniEco Medical Autoclave Tape · CliniEco Medical Bowie-Dick Test Pack · CliniEco Medical Steam Chemical Integrator · Wholesale & clinic accounts · How our sterilization monitoring is verified
Products referenced in this guide
What is the core difference in plain terms?
A Class 5 indicator is built to behave like a broad process integrator: it responds across a range of cycle conditions in a way that correlates with lethality. A Class 6 indicator is cycle-specific by design. It is matched to a defined cycle, such as 134°C for a specified hold time, and it is not intended to be used on a different cycle profile.
| Property | Class 5 integrator | Class 6 emulating indicator |
|---|---|---|
| ISO 11140-1 role | Integrating indicator | Emulating indicator |
| Cycle specificity | Broad, responds across conditions | Matched to a specified cycle |
| Typical placement | Inside pack or PCD | Inside pack or PCD |
| Use on a different cycle | Generally the intended flexibility | Not appropriate; the indicator is cycle-specific |
| Relation to BI monitoring | Reduces, but does not replace, BI use | Same: it does not replace BI monitoring |
Which one should a clinic buy?
The answer follows from your cycle list. A practice that runs one steam cycle type, consistently, can use a Class 6 indicator matched to that cycle and get a very tight read on parameter exposure. A practice running multiple cycle types, including a flash cycle, is better served by a Class 5 integrator that is not tied to a single profile.
Most dental offices run more than one cycle type, which is why the practical default in Canadian dental reprocessing is a Class 5 or a Class 4 indicator with clear documentation of which cycle each pack went through.
Does either class replace a biological indicator?
No. A chemical indicator shows that the physical conditions were present at a location. A biological indicator shows that spores were killed. A chemical indicator pass, whichever class, does not certify sterilisation and is not a substitute for the routine spore test your regulator expects.
Class 5 vs Class 6: which one should a clinic buy?
Print this table and keep it with the indicator policy. Print this table
| Measure | Class 5 — integrating | Class 6 — emulating | What it means for you |
|---|---|---|---|
| ISO 11140-1 basis | Responds to all critical variables | Set to a specific cycle’s parameters | Both are internal indicators |
| What it tells you | A result equivalent to a spore kill | The named cycle stayed in range | Neither one replaces the biological indicator |
| Cycle flexibility | Usable across a range of steam cycles | Matched to one stated cycle | Match the class to the cycles you actually run |
| Mistake to avoid | Reading it as proof of sterility | Using a 134 °C indicator on a 121 °C cycle | Record the indicator class in the log |
ISO 11140-1 separates indicators by how much information they carry, not by price. Choose by the cycles your sterilizer runs, and keep the class and lot on the sterilization record.
What are the most common mistakes?
Using a Class 6 indicator on a cycle it was not specified for, which produces a reading that means nothing. Reading a chemical indicator as a pass/fail result rather than as a record of conditions. And covering the indicator with tape or a label so the colour change is partly hidden at inspection time.
One documentation habit prevents most of this: record which cycle each pack ran, and store the indicator alongside the cycle printout for that day. If a pack is later questioned, the pairing is the evidence.
How should the indicator choice be recorded in the sterilization log?
The indicator itself is only half of the record. For each load the log should carry the sterilizer identifier, the cycle type and its parameters, the date, a load or pack identifier, and the result of the internal indicator. ISO 11140-1 sorts chemical indicators into six classes, so recording which class was used - and its lot number - lets a reviewer confirm that the indicator matched the cycle it was run on.
A Class 6 strip and a Class 5 integrator are not interchangeable records. When a log shows a Class 6 indicator against a cycle the strip was not specified for, the entry no longer demonstrates anything about that load. Keeping the class and the cycle on the same log line is what makes the pairing checkable.
What does a chemical indicator never replace?
A chemical indicator pass is not a release test on its own. The indicator records that the physical conditions reached its location; it says nothing about spores. The direct test of spore kill is the biological indicator, and provincial dental guidance sets the frequency at which that test must run. The two records sit side by side because they answer different questions: the indicator covers every pack, and the biological indicator covers the sterilizer on the schedule the regulator sets.
Neither layer replaces the sterilizer printout. Physical monitoring shows the cycle followed the profile it was programmed for, the chemical indicator shows what reached a point inside the pack, and the biological indicator shows lethality. A file that holds all three answers the question a reviewer will actually ask - whether this load, on this day, on this sterilizer, was monitored.


Which internal indicator a practice records per load is a policy question, and it can be put to a sterilization compliance specialist.
Related Reading
- ISO 11140-1 explained: chemical indicator classes
- BI vs chemical indicators in sterilization monitoring
- Sterilization compliance hub
- free Ontario sterilization compliance log
Frequently Asked Questions
What is the difference between a Class 5 and a Class 6 chemical indicator?
A Class 5 indicator is an integrator that responds to the critical variables of the sterilisation process across a range of conditions. A Class 6 indicator is an emulating indicator, specified for a particular cycle profile.
Can a Class 6 indicator be used on any steam cycle?
No. A Class 6 indicator is designed for a specified cycle, so using it on a different profile produces a reading that is not meaningful for that load.
Do chemical indicators replace biological indicator testing?
No. Chemical indicators record the process conditions at their location. Biological indicators verify spore kill, and routine biological indicator monitoring is what provincial dental guidance expects.
Class 5 vs class 6 indicator 121°C 30 minutes steam sterilization
A Class 5 integrating indicator reacts to all critical variables and carries stated values correlated to a biological indicator; a Class 6 emulating indicator is matched to one specified cycle. For a 121 °C / 30 minute cycle you need either a Class 6 indicator validated for that cycle or a Class 5 integrator - a Class 6 built for a different time and temperature does not cover it.
Can a Class 5 indicator be used on any steam cycle?
Yes. A Class 5 integrator is not tied to a single profile: it is designed to respond to the critical variables across a range of cycle conditions, which is why it suits a practice that runs more than one cycle type. It still records conditions rather than sterility, so it does not replace biological indicator monitoring.
Ordering for a clinic, lab or care home? Wholesale and multi-site ordering covers case pricing and account setup, and the B2B wholesale collection lists the lines stocked for institutional buyers.
Start with a trial: Biological Indicator 5-Pack Trial (free, ships free) for a single sterilizer, or request the Rapid Reader seed trial for multi-site monitoring programs.
CliniEco Medical is a licensed medical device establishment (MDEL #35334).
Where to Buy Biological Indicators in Canada
CliniEco Medical supplies these from Ontario with published CAD pricing (MDEL #35334) — no quote required, and each pack ships with the lot number printed on it so your monitoring record stays traceable.
| Format | Pack size | Price (CAD) | |
|---|---|---|---|
| 24-hour self-contained | 25-pack | $69.99 | 24-hour self-contained biological indicators — 25-pack |
| 24-hour self-contained | 100-pack | $189.00 | 24-hour self-contained biological indicators — 100-pack |
| 3-hour rapid fluorescence | 50-pack | $249.99 | 3-hour fluorescence biological indicators — 50-pack |
Round Out Your Sterilization Setup
A biological indicator is one link in the chain — these are the pieces it works with:
- Sterilization pouches — Class 4 dual-indicator, 200-pack — the packaging the indicator rides inside
- Autoclave indicator tape — 3-roll set — the external chemical indicator on every pack
- Class 5 chemical integrators — 100-pack — the in-pack check that pairs with your biological indicator
- Sterilization roll — 50 m pre-cut sheets for larger instruments
- Constant-heat pouch sealer — 200 °C, 12 mm seal — for consistent pouch closures
Which format does your sterilizer actually need?
Match the readout time to how fast you need the result: a 24-hour self-contained indicator works in any gravity or pre-vacuum cycle with a standard incubator, while a 3-hour fluorescence tube needs the matching reader. Running one cycle type per day, the 25-pack covers a month; busier clinics move to the 100-pack and cut the per-test cost.
How much do spore tests cost in Canada?
Published pricing runs $2.80 per test on the 25-pack down to $1.89 on the 100-pack — no distributor quote, no account needed.
Not sure which format your sterilizer needs? Generate a free sterilization log sheet first — it maps your cycles and tells you the pack size that fits. Questions about your setup? Ask a Compliance Specialist.