Quick facts
- ANSI/AAMI ST8 and ANSI/AAMI ST79 are not two editions of the same document. ST8 writes requirements for the sterilizer; ST79 writes recommended practice for the facility that runs it, and neither one specifies the sterilization consumables you buy.
- ST8's stated objective is to set minimum labeling, safety, performance and testing requirements for steam sterilizers in health care facilities with a chamber volume greater than 56.63 litres (2 cubic feet).
- A steam purity number — non-condensable gas content, dryness value, superheat — does not come from ST8. The published limits sit in EN 285, clause 13.3, and a Canadian facility's utilities content sits in CAN/CSA-Z314:2023.
- ST8 contains a test schedule that a clinic never repeats: air removal, air leak rate, chamber temperature, exposure timer accuracy, biological performance against defined challenge packs.
- Weekly biological indicator testing is the United States baseline in ST79. Ontario expects a biological indicator for every sterilizer on each day it is used, and for each type of cycle.
ANSI/AAMI ST8 and ANSI/AAMI ST79 are often quoted together as if one superseded the other, or as if ST8 were the short version of ST79. Neither reading survives contact with the documents. ST8 is a performance and testing standard addressed to whoever builds and certifies the sterilizer; ST79 is a recommended practice addressed to the department that runs it. A clinic that buys equipment against ST8 and monitors it against ST79 is using both correctly — and a clinic that expects ST8 to tell it how often to run a biological indicator is looking in the wrong document.
This matters at purchasing and at audit, because the two failures look identical on paper: a quote claims "compliant with AAMI standards" without saying which one, and a file contains a sterilizer certificate that proves the machine was type-tested at the factory rather than that the installation in your decontamination room performs. The packaging you buy is a useful worked example of the same split, because a box of Class 4 self-sealing pouches carries a process indicator that tells you the pack has been through a cycle, while the question of whether the cycle was valid belongs to a different document entirely.
What does ST8 actually cover, and what does ST79 cover?
The cleanest way to read the pair is by object: ST8 governs the machine and its test methods, ST79 governs the decisions a reprocessing department makes with the machine. The table below sets out the division, with the Canadian layer in the last column, because a Canadian clinic answers to a third document for several of these items.
| Question | ANSI/AAMI ST8 | ANSI/AAMI ST79 | Where a Canadian clinic's obligation sits |
|---|---|---|---|
| Object of the document | Minimum performance and testing of hospital steam sterilizers above 56.63 L | Recommended practice for steam sterilization and sterility assurance in health care facilities | CAN/CSA-Z314:2023, the consolidated reprocessing standard |
| Who the requirements address | Sterilizer manufacturer and the certifying test house | The facility: managers, technicians, infection control | The facility, plus provincial guidance |
| Steam supply and purity | Not a purity specification; supply is an input the machine is expected to tolerate | Practice expectations for the utility, without a numeric table | Utilities content in CAN/CSA-Z314:2023; provincial water and steam guidance |
| Air removal and leak rate | Explicit tests: air removal for dynamic-air-removal machines, leak rate for prevacuum machines | Load configuration and monitoring practice that assume the machine works | Verifier or service provider evidence, retained in the sterilizer file |
| Routine biological monitoring | Biological performance demonstrated during type and performance testing | At least weekly, preferably daily, plus every implant load — the United States baseline | Ontario: each sterilizer, each day used, each cycle type |
| Cycle records | Cycle documentation requirements on the machine, with example printouts | What the facility records and reviews after the cycle | Log book retention and review expectations |
| Jurisdiction and weight | United States national standard, voluntary | United States recommended practice, voluntary | National standard of Canada; referenced by provincial expectations |
Two cells in that table deserve to be read twice. The first is steam purity: neither ST8 nor ST79 is the document that publishes a numeric purity limit, which is why a facility that wants a number has to go to EN 285 or to the utilities content of CAN/CSA-Z314:2023. The second is monitoring frequency: the frequency a Canadian clinic must meet is a provincial expectation, not an AAMI one.
Which document carries an actual steam quality number?
If the audit question is "what is the maximum non-condensable gas content of the steam entering the chamber", the answer is in EN 285, clause 13.3, and it is expressed as three physical tests rather than one figure. The values are widely reproduced by testing laboratories and water-treatment specialists because the tests are what a steam quality survey actually performs.
| Test | EN 285 limit for steam supplied to the sterilizer | What a failure looks like in the load |
|---|---|---|
| Non-condensable gases | Not more than 3.5 % (v/v) | Air pockets hold a cooler pocket of gas against the load; indicators can look acceptable while a challenge pack fails |
| Dryness value | At least 0.95 | Wet steam arrives with entrained droplets; pouches and wraps come out damp |
| Superheat | Not more than 25 °C above saturation | Steam behaves like a hot gas, dries the load unevenly and can bake residue onto instruments |
These are European product-standard values, not Canadian legal limits, and they are measured at the point where steam enters the sterilizer rather than at the boiler. That location is the whole point: a facility can hold a valid boiler certificate and still deliver out-of-limit steam at the chamber, because the piping, the filters, the pressure reducing station and the air removal behaviour of the machine all sit between the two.
For the test procedures themselves, the practical sequence and the instrumentation are set out in steam quality testing: non-condensable gases, dryness fraction and superheat, which is the operational companion to this article.
What does ST8 test that a clinic never repeats?
The table of contents that AAMI's distributors publish for ST8 reads like a test schedule rather than a policy: labeling, pressure vessel certification, electrical components, corrosion resistance, air filters, interlocks, prevention of thermal hazards, chamber temperature, a thermometric test connection, the exposure timer, pressure measurement, cycle documentation, biological performance, mechanical air removal, air leak rate, and performance certification with recordkeeping. Annex B then shows what a cycle printout is expected to contain.
| ST8 requirement area | What it establishes | Who performs it | What a clinic should hold |
|---|---|---|---|
| Chamber temperature, pressure, exposure timer | The instruments that produce the numbers on the printout are accurate enough to be trusted | Manufacturer, then service provider at installation and at calibration | Calibration certificates with the instrument identified |
| Mechanical air removal and air leak rate | The machine can remove air and hold vacuum as designed | Manufacturer's type test, repeated on site after installation or major repair | Commissioning report, not only the brochure |
| Biological performance with defined challenge packs | The cycle kills spores in a specified worst case (fabric pack, wrapped instrument pack, abbreviated cycle) | Manufacturer during qualification; the same packs are what a verifier uses | Qualification report naming the challenge pack used |
| Cycle documentation | The printout records what the standard expects a cycle record to contain | Machine firmware, verified at commissioning | A printout you can read, with time, temperature and pressure legible |
| Performance certification and records | A documented statement that the machine met the requirements, traceable to the tests | Manufacturer and the certifying body | The certificate, filed with the installation date |
The practical consequence is a split in what evidence means. A type-test report shows the model can perform; an installation and calibration record shows this machine, in this room, with this steam supply, performs. A purchasing file that contains only the first is answering a different question from the one an assessor asks.
Where does the daily monitoring obligation come from?
Not from ST8, and not from ST79 either, if you work in Ontario. The province's expectations are expressed through the Royal College of Dental Surgeons of Ontario's infection prevention and control guidance and through Public Health Ontario's provincial infectious disease advisory material, and they are written in terms of frequency per sterilizer, not per facility: every sterilizer, on each day it is used, and for each type of cycle.
ST79's contribution is a different sentence, and it is the one most often borrowed out of context: a biological indicator at least weekly, preferably daily, with every load containing implants. That is the United States recommended-practice baseline. It is not the Ontario requirement, and citing it as if it were produces the most common cross-jurisdiction error in this subject — a policy document that looks compliant in a United States survey and fails a Canadian practice visit.
| Statement | Where it comes from | How to use it |
|---|---|---|
| Every sterilizer, each day used, each cycle type | Ontario guidance | The frequency a policy in Ontario has to state |
| At least weekly, preferably daily, plus every implant load | ANSI/AAMI ST79, United States recommended practice | A comparison line in a policy, labelled as a United States baseline |
| Steam purity tested at defined intervals | EN 285 test methods, applied through the facility's own schedule | The schedule a service provider performs, documented |
| Validation and routine control of the process | ISO 17665 | The frame that tells you what a validation report has to establish |
The Canadian frame for the last row is the consolidated national standard: the old CSA Z314.3 for steam and the other part-standards were folded into CAN/CSA-Z314:2023, which is why a clause map drawn against the withdrawn part-editions no longer lines up. That consolidation is traced clause by clause in CSA Z314.3 to CAN/CSA-Z314:2023: the Canadian steam sterilization clause map.
How do you read a wet load without the standard in hand?
A wet pack is the visible end of one of four different causes, and the four are separated by three different tests plus one load-side check. Wet steam is a dryness-value problem. Air that the machine failed to remove is a non-condensable gas problem. Steam hotter than saturation is a superheat problem, usually created by a pressure reducing valve or an undersized pipe run. The fourth cause is on the load side — an overloaded chamber, a drying phase too short for the packaging, or condensate pooling in a folded wrap — and it is assessed by the load dryness test rather than by the steam supply tests.
Provincial guidance is deliberately blunt about the response: a pack that is visibly damp or damaged is repackaged and reprocessed rather than released, and storage humidity is monitored because a dry pack stored at high humidity becomes a wet pack without any sterilizer fault at all. Instrument residue and staining are a related but different signal — they point upstream to the water and chemistry used before sterilization rather than to the steam itself, which is what an independent review concluded in the Whitehorse General Hospital case, where residue and staining on instruments traced to the use of utility water rather than critical water in the final rinse against a naturally hard water supply, and 165 surgeries were postponed. The hospital's own account is worth reading alongside any steam quality procedure, because it shows how a water problem presents as a sterilization failure.
What should a clinic ask a service provider in writing?
- Which document is the certificate against? "AAMI compliant" is not an answer. Ask for the ST8-based performance certification for the model, and separately for the installation and calibration record for this serial number.
- What steam quality tests were run, to which limits, and at which point of the supply? The answer should name the three tests, the limits, and the sampling location.
- What challenge pack was used for the biological performance demonstration? The standard's own packs are defined objects; a report that says "spore test passed" without naming the pack has not told you what was challenged.
- Which instruments are calibrated, and against what? Chamber temperature, pressure and the exposure timer are the three whose errors propagate straight into a released load.
- What is the re-test trigger? Installation, major repair, a change to the steam supply, and a failed load are the events that reopen the question.
- Where do the records live, and for how long? A file that the facility cannot produce at a practice visit is a file that does not exist.
Buying consumables is the other half of the same question, because the packaging and monitoring items you stock determine what can be observed at all. Pouches, tape and indicators record that a load went through; the biological indicator is the only item on the shelf that speaks to lethality, and the 24-hour steam biological indicator is the one whose incubation window sets how long a load has to wait before it can be released without quarantine. A constant-heat pouch sealer does not change the standard's requirements, but a seal that fails invalidates the pack before the sterilizer is ever involved.
What does this change for a purchase or a tender?
Three things, and they are all about which piece of paper you accept as the answer to which question.
First, separate the machine from the practice in the specification. A tender that asks for "compliance with AAMI steam sterilization standards" invites a brochure answer. A tender that asks for the ST8-based performance certification, the commissioning record with the air removal and leak-rate results, and the calibration certificates for chamber temperature, pressure and timer gets documents that can be checked.
Second, ask the water and steam question before the equipment question. Steam purity is a supply property, and a clinic cannot fix it by buying a different sterilizer. If the steam comes from a house boiler, the tests in EN 285 clause 13.3 are the ones that decide whether the machine can do what its certificate says.
Third, treat the monitoring consumables as part of the evidence chain rather than as stock. A policy that cites the correct frequency but buys indicators that do not match the cycle type, or stores them outside their stated conditions, has a documentation problem that a practice visit will find faster than a surveillance program will.
For the wider frame these answers sit inside — loading, packaging, release and records across the Canadian, United States and European documents — start at the sterilization compliance hub. The fields worth capturing when a load leaves the decontamination room, including the sterilizer identity, cycle type and result fields this article refers to, are laid out in the compliance log centre, which runs in a browser without an account and can be printed as a blank sheet.
Ordering for a clinic, a lab or a care home? Wholesale and multi-site ordering covers case pricing and account setup, and the B2B wholesale collection lists the lines stocked for institutional buyers. Reselling? become a distributor.
Have a question about your own facility? Send it in and you will get a written answer specific to your setup, with the regulation or standard it is based on cited. Ask your compliance question.
Related reading
- CSA Z314.3 to CAN/CSA-Z314:2023: the Canadian steam sterilization clause map — the Canadian clause-by-clause counterpart to this article.
- Steam quality testing: non-condensable gases, dryness fraction and superheat — how the three EN 285 tests are actually run.
- Steam penetration in dense instrument sets: why weight matters — the load-side variable that no supply-side test can correct.
Frequently Asked Questions
Does ANSI/AAMI ST8 apply to a small tabletop autoclave?
Read the scope before anything else. ST8 is written for steam sterilizers with a chamber volume greater than 56.63 litres, which is 2 cubic feet, so a benchtop unit below that threshold is outside its scope. Small steam sterilizers are addressed by separate standards, including EN 13060 in the European system, and the Canadian expectation still arrives through CAN/CSA-Z314:2023 and provincial guidance regardless of which equipment standard the machine was built to.
If ST8 does not set steam purity limits, why is it quoted in steam quality discussions?
Because the two questions are adjacent and easy to confuse. ST8 covers the sterilizer's ability to remove air, hold vacuum and document the cycle; steam purity is a property of the supply arriving at the machine, and its numeric limits sit in EN 285 clause 13.3. A purchasing file that quotes ST8 in answer to a steam quality question has changed the subject, and the usual reason is that the supplier holds an ST8 certificate and does not hold a current steam survey.
Is a biological indicator required every day in Canada?
In Ontario, yes: the expectation is a biological indicator for every sterilizer on each day it is used, and for each type of cycle. The sentence that circulates internationally — at least weekly, preferably daily, plus every implant load — is the ANSI/AAMI ST79 recommended practice for the United States. Both statements are true; only one of them describes an Ontario obligation, and a policy that swaps them is a documentation defect rather than a debate.
What is the difference between a performance certification and a calibration record?
The certification says the model met the standard's requirements under the tests the standard defines. The calibration record says the instruments on your machine were reading correctly on a given date. Neither substitutes for the other: a certified model with a drifting timer releases loads against numbers that are wrong, and a freshly calibrated machine of a model that never demonstrated the required performance is accurately reporting a process nobody qualified.
Where should the steam quality sample be taken?
At the point where steam enters the sterilizer, not at the boiler and not at a downstream drain. The tests in EN 285 clause 13.3 are written for the supply at the sterilizer inlet, because piping runs, filters, pressure reducing valves and the machine's own air removal behaviour all sit between the boiler and the chamber. A sample taken upstream answers a question about the plant; a sample taken at the inlet answers the question the load depends on.
Can a wet pack be released if the indicators turned?
No. A turned indicator records that the pack was exposed to a cycle, and provincial guidance treats a visibly damp or damaged pack as one to repackage and reprocess rather than release. The indicator is a process indicator; a wet pack is evidence that something about the process or the load was wrong, and the correct response is to find out which of the four causes applies rather than to read the indicator as a release decision.
How often does the air removal or leak-rate test have to be repeated?
That is set by the facility's own schedule and by what the machine's documentation states, not by a single number in ST8. The triggers that matter are installation, major repair, a change to the steam supply or the piping, and any failed load that points to air. Recording those events and the re-test against them is what turns a commissioning test into an ongoing assurance, and it is the part most often missing from a file assembled at purchase.
Every CliniEco Medical product is manufactured under an ISO 13485 quality management system and distributed under Health Canada MDEL #35334. If your question is which document governs a specific machine or a specific record in your clinic, our specialists will read the standard with you rather than paraphrase it.
Sources
- ANSI/AAMI ST8:2013/(R)2018, Hospital steam sterilizers (AAMI catalogue entry)
- ANSI/AAMI ST8:2026, Hospital steam sterilizers — scope and objective abstract
- ANSI/AAMI ST8 table of contents (published by the standard's distributor)
- ANSI/AAMI ST79:2017/(R)2022 with amendments A1–A4:2020
- ANSI/AAMI ST79:2017 explanatory white paper
- SIST EN 285:2016, Sterilization — Steam sterilizers — Large sterilizers (clause structure: 13.3 steam supply, 8.3 load dryness, 20 load dryness test)
- EN 285 steam quality limits as applied in testing practice: non-condensable gases, dryness value, superheat
- Autoclave steam quality: how contaminated steam compromises sterilisation
- ISO 17665:2024, Sterilization of health care products — Moist heat
- CSA Z314.3-18, Effective sterilization in health care facilities by the steam process (predecessor to the consolidated Canadian standard)
- Public Health Ontario, provincial infectious diseases advisory: cleaning, disinfection and sterilization in health care settings
- Royal College of Dental Surgeons of Ontario, infection prevention and control
- Centers for Disease Control and Prevention, disinfection and sterilization in healthcare facilities
- ISO 11138-1:2017, Sterilization of health care products — Biological indicators — Part 1: General requirements
- ISO 11139:2018, Sterilization of health care products — Vocabulary
- Yukon Hospitals: sterilization incident report and quality performance reports
- Hospital News: sterilization failure halts surgeries — lessons for hospitals nationwide