Which Standards Apply to Face Mask in Ontario Clinics

Aurelia Level 2 medical face mask box with ASTM Level 2 badge

A face mask order in Ontario rarely fails on price. It fails on paperwork: a clinic buys a carton that says "Level 2", then cannot say which standard the level refers to, which test produced it, or which obligation made the clinic buy a medical mask at all. The standards question is answerable in four layers — the product standard, the Canadian device framework, the Ontario workplace duty, and the professional or facility standard that applies to the setting — and each layer asks for a different piece of evidence.

This guide works through those four layers in the order an audit would, then shows what a defensible mask file looks like for an Ontario dental office, medical clinic or long-term care home.

Which standards apply to a face mask sold to an Ontario clinic?

Four references do most of the work, and they are not interchangeable. ASTM F2100 is the performance specification that establishes mask levels. EN 14683 is the European specification that Ontario buyers meet constantly because a large share of imported masks are typed to it. The Canadian medical device framework decides whether the mask may be sold here at all. And the professional or facility standard — the the RCDSO infection prevention and control standard infection prevention and control standard for dentistry, or Public Health Ontario guidance for clinical settings — decides which mask the staff must wear for which task.

The common mistake is to treat "Level 2" as a legal category. It is a performance band inside a voluntary consensus standard; what makes the mask sellable in Canada is the device framework, and what makes the choice defensible is the setting-specific standard. A clinic that can name all three, and produce the documents behind them, is answering the audit question before it is asked.

Four references an Ontario mask buyer meets, and what each one settles
Reference What it governs What it actually tests Where a clinic meets it
ASTM F2100 Performance levels for medical face masks (Level 1 to 3) Bacterial and particle filtration, differential pressure, synthetic blood penetration, flammability The specification sheet and level claim on the carton
EN 14683 European mask types (Type I, II, IIR) Filtration efficiency, breathability, and splash resistance for the R suffix Imported stock, and quotes written to a European specification
Canadian medical device framework Whether the mask may be sold in Canada, and who is accountable for that Establishment licensing of the importer or distributor for Class I devices The supplier's licence number and the device labelling
Setting-specific IPAC standard Which mask staff must wear for which task Procedure-level exposure assessment, training, and records The RCDSO standard for dentistry, PHO guidance for clinical settings

One further distinction matters for procurement: a mask can meet ASTM F2100 and still be the wrong mask for a task. F2100 describes barrier and breathability performance under test conditions; it says nothing about fit, about how long a mask can be worn, or about whether the wearer has been fit tested for a respirator. Those are separate questions with separate answers.

For a concrete example of how the level language appears on a real product line, the Aurelia Level 2 mask stocked for Ontario clinics shows the claim, the level badge on the carton and the specification sheet that should sit behind it. Comparing that carton against the table above is the fastest way to see whether a supplier's level claim is a tested result or a design intent.

Aurelia Level 2 medical face mask box, 50 masks per box, with ASTM Level 2 badge on the front panel

What does ASTM F2100 actually measure?

ASTM F2100 evaluates five properties, and the levels are built from three of them plus a fluid-resistance threshold. Bacterial filtration efficiency (BFE) and particle filtration efficiency (PFE) are measured at defined particle sizes; differential pressure measures breathability; synthetic blood penetration at increasing pressures defines the splash rating; and flammability is reported as Class 1 for medical masks. The specification is published by ASTM International and revised periodically, so a claim should name the edition.

ASTM F2100 levels against the properties they are built from
Property What it measures Level 1 Level 2 Level 3
Bacterial filtration efficiency (BFE) Filtration of bacteria-sized particles at the stated test flow 95% or higher 98% or higher 98% or higher
Particle filtration efficiency (PFE) Filtration of sub-micron particles 95% or higher 98% or higher 98% or higher
Differential pressure Breathability — resistance to airflow Below 5.0 mm H2O/cm2 Below 6.0 mm H2O/cm2 Below 6.0 mm H2O/cm2
Synthetic blood penetration Splash resistance at increasing pressure 80 mmHg 120 mmHg 160 mmHg
Flammability Flame spread of the mask material Class 1 Class 1 Class 1

The thresholds are what make level comparisons meaningful. Level 1 sits at 95 per cent for both BFE and PFE with a splash resistance of 80 mmHg. Levels 2 and 3 both require 98 per cent filtration, and differ on fluid resistance — 120 mmHg for Level 2 and 160 mmHg for Level 3 — with a slightly looser breathability allowance than Level 1. That is why a Level 1 mask is not simply "a weaker Level 3": the two are designed for different exposure profiles, and in a procedure with visible splashing the fluid-resistance number is the one that decides.

Under EN 14683 the logic is similar but the labels differ: Type I and Type II set filtration at 95 and 98 per cent respectively, and the "R" suffix marks splash resistance tested at 120 mmHg. An EN 14683 Type IIR mask and an ASTM F2100 Level 2 mask are therefore aimed at comparable exposure, but the two claims rest on different test methods and should not be quoted as equivalent without the underlying reports.

CliniEco Medical 3-ply ASTM Level 2 procedural face masks in clinic packaging

Does an Ontario clinic need ASTM F2100 or EN 14683?

Neither standard is named in Ontario law, and that is precisely why the question keeps coming back. What Canadian law requires is that the mask be a legally saleable medical device: Health Canada regulates masks as medical devices, and for Class I devices the route is an establishment licence held by the importer or distributor rather than a device licence for the product. CliniEco Medical holds MDEL #35334 and sells into Canadian clinics on that basis.

What the professions require is a mask appropriate to the task. In dentistry, the RCDSO infection prevention and control standard requires PPE matched to the procedure and to anticipated exposure, and the accompanying PHO dental IPAC checklist walks through the items expected in a dental operatory. In hospital and clinic settings, CDC isolation precautions guideline sets out source control and mask use by precaution category, while Public Health Ontario IPAC guidance translates that into Ontario practice. An inspector reading a mask file is checking whether the clinic chose a mask against a stated criterion — not whether a particular brand appears on a list.

Practically, ASTM F2100 is the specification most Canadian suppliers document against, because it maps cleanly onto the level language used in procurement and audit. A clinic that buys EN 14683 product can still build a defensible file; it simply needs the Type and the R-suffix documented, plus the test report, so the comparison to a level can be made in writing rather than assumed.

What does Ontario law require of the clinic itself?

Three obligations sit on the clinic rather than the supplier. The first is the general duty in Ontario's Occupational Health and Safety Act to take every precaution reasonable in the circumstances for the protection of a worker — Ontario's Occupational Health and Safety Act — which is the provision behind most written PPE programmes in Ontario workplaces, including clinics. The second is the setting-specific standard: dental offices follow the RCDSO IPAC standard, and licensed long-term care homes operate under O. Reg. 246/22 under the Fixing Long-Term Care Act, 2021 with its infection prevention and control programme requirements. The third is public health oversight — local public health units inspect IPAC practice, and the Ontario Ministry of Health and Ontario's long-term care ministry publish the guidance those units work from.

None of those instruments specifies a mask level by number. Each requires a documented decision: a hazard assessment or procedure list, a mask selected against it, staff trained on donning and doffing, and a record. That is why the mask file, not the mask, is what an inspector actually reads. IPAC Canada publishes practical IPAC material that many Ontario clinics use to structure exactly this kind of programme documentation.

How should an Ontario clinic document mask selection?

Keep it to one page per clinical area and review it when the procedure mix changes. The file should tie the procedure to an exposure profile, the exposure profile to a level, and the level to the product actually stocked — with the supplier's documentation attached rather than summarised. Where a clinic stocks two levels, the page should say which rooms hold which, because the failure mode in a mixed stockroom is a Level 1 box in a room where splashing is routine.

What an Ontario mask file should contain, by record
Record What it shows Who keeps it Reviewed when
Procedure-to-level list Which mask level applies to which procedure or room Clinical lead Procedure mix changes
Specification sheet Standard, edition, level, and the test basis for the claim Procurement Supplier or factory changes
Receiving log Lot numbers and dates, so recalls can be scoped Stores or front desk Every delivery
Training record Donning and doffing training, with the mask in use at the time IPAC lead Annually and after product changes
Supplier licence The establishment licence number behind the import or distribution Procurement Annually

Two records are worth more than they cost. One is the receiving log with lot numbers, which turns a recall notice into an actionable list instead of a shelf-by-shelf search. The other is the training record for donning and doffing, because the mask only performs as specified if it is worn and removed correctly — the sequence in CDC isolation precautions guideline is the reference most Ontario programmes cite.

For clinics that also reprocess instruments, the mask decision sits alongside the reprocessing programme rather than apart from it: Public Health Ontario's reprocessing guidance covers the workflow, and Public Health Ontario's reprocessing checklist for dental settings is the checklist most Ontario dental offices audit against. CliniEco Medical supplies Ontario clinics with ASTM-rated masks, including Aurelia Level 2 masks made in Canada and CliniEco Medical 3-ply Level 3 masks, and can provide the specification documentation that a mask file needs.

Reselling or buying for a facility? become a distributor for wholesale and multi-site ordering.

Where to go next. Print the downloadable IPAC and PPE SOP pack to sit at the front of your mask file, estimate monthly volume with the clinic usage calculator, and use the compliance question form if you want an answer written against your own procedure list. For stock, CliniEco Medical 3-ply Level 3 masks cover splash-heavy procedures alongside the Level 2 line above. CliniEco Medical supplies Ontario clinics, dental offices and long-term care homes under MDEL #35334, and wholesale accounts carry institutional pricing.

Related Reading

Related Reading

Frequently Asked Questions

Is a Level 1 mask enough for an Ontario dental office?

It depends on the procedure, and the file should say so. Level 1 masks are rated for 95 per cent filtration with 80 mmHg splash resistance, which fits routine administrative and low-splash contact but not procedures generating visible spatter. The the RCDSO infection prevention and control standard requires PPE matched to anticipated exposure, so the defensible pattern is a procedure list that names which mask level applies to each, reviewed when the procedure mix changes.

Do face masks sold in Ontario need a Health Canada licence?

Medical masks are regulated as medical devices in Canada, and the compliance route depends on the class: Class I devices are sold under a medical device establishment licence held by the importer or distributor, rather than under a device licence for each product. That is why a clinic should ask for the seller's establishment licence number and the product's specification sheet — the Health Canada medical devices programme explains the framework, and the two documents answer different questions.

Can a clinic use EN 14683 masks instead of ASTM F2100?

Yes, provided the file documents the Type and the R-suffix rather than a level. EN 14683 Type IIR is tested for splash resistance at 120 mmHg, which is comparable in intent to ASTM F2100 Level 2, but the two claims rest on different methods. Quote the standard you can produce a report for; converting between them without the reports is where mask files become indefensible.

How long can a mask be worn in an Ontario clinic?

Follow the manufacturer's instructions for use and the setting's policy — there is no single provincial number. What matters for audit is that a written rule exists: when a mask is replaced, what happens if it becomes damp or soiled, and how staff know. IPAC Canada and Public Health Ontario IPAC guidance materials give the practical framing most Ontario clinics adopt, and the rule should be written into the room's PPE card rather than left to habit.

What documents should a clinic keep for a mask order?

Four: the specification sheet naming the standard and edition, the lot number recorded at receiving, the supplier's establishment licence number, and the clinic's own selection record showing which level applies to which procedure. Those four answer the questions a public health inspector or an IPAC auditor actually asks, and they are all obtainable before the first order rather than after the first problem.

CliniEco Medical supplies Ontario clinics, dental offices and long-term care homes under MDEL #35334, and the specification sheets behind each mask level named in this guide are available on request. Last updated: 10 November 2026.

Vous travaillez déjà avec des cliniques ? Devenez représentant régional.