Quick facts
- A positive biological indicator is treated as a failed sterilization until an investigation proves otherwise: the sterilizer comes out of service, the load is quarantined, and the look-back starts on the same day.
- The Ontario standard of practice does not stop at "investigate". It requires a written log in which the daily operation of every sterilizer is reviewed and documented, kept for at least 10 years after the last entry.
- The self-audit form used in Ontario dental practices asks for a biological indicator plus a control test once daily, for each type of cycle — a paired test, not a single vial.
- Operator error is the most common cause of a positive biological indicator, ahead of equipment failure, which is why the sequence spends its early steps on packaging, loading and the record rather than on the machine.
- After a repair, the return-to-service evidence is three consecutive biological indicator results and, for dynamic air removal sterilizers, three consecutive Bowie-Dick tests.
A positive spore test is the one result in a dental office that converts a routine day into a documented investigation. The clinical decision is narrow — do not use the sterilizer, do not release the load — but the paperwork that follows is where practices lose points at a practice visit, because the sequence produces six different records, completed by different people, and an assessor will ask for all six.
The investigation is only as readable as the test behind it. The 24-hour steam biological indicator is the format most dental practices run daily, and its read time is what decides how long an implant load stays in quarantine while the paperwork closes.
This article sets out the six steps as a protocol, then maps each step to the document it produces and the person who signs it. It is written for the dentist who owns the policy, the office manager who keeps the file, and the infection control lead who has to answer for it. The regulatory frame is Ontario's, with the United States baseline noted where the two differ, and the equipment-side questions are the same ones that apply to any steam process.
What has to happen before anyone touches the sterilizer again?
The first three actions are simultaneous, not sequential. The sterilizer is taken out of service and labelled. Every load processed since the last negative biological indicator is quarantined. The result itself is verified before the machine is blamed, because the Ontario cause list starts with operator error and includes indicator handling errors that look like machine failures.
Ontario's investigation flowchart sets out the order: place the sterilizer out of service, temporarily quarantine instruments back to the previous negative biological indicator, and check the printout or electronic record of the physical parameters. From that point the path splits. If the cause is immediately identified and is confined to one load or one pouch, the load is reprocessed. If the cause is unknown, the machine stays out of service until the service provider has repaired it, and the practice works back to the last negative result.
That branching is the part practices flatten into a single step. It should not be flattened, because the two branches produce different evidence: a reprocessed load with a documented cause, or a repair report with a requalification record. An assessor can tell which one happened from the file, and a file that shows neither is a file that was written after the fact.
The documents themselves are published by the Royal College of Dental Surgeons of Ontario as part of its infection prevention and control material: the standard of practice, the self-audit review form, the potential causes of a positive biological indicator, and the steps to investigate flowchart. Public Health Ontario's provincial advisory carries the same requirement in requirement language, and attributes it to the CSA sterilization standard: a biological indicator is to be used each day the sterilizer is used, and for each type of cycle used that day.
The six-step protocol
The table below is the protocol in operating order. The fourth column is the point most often missed: every step leaves a record, and the record has a different owner.
| Step | Action | Decision point it resolves | Record it must leave |
|---|---|---|---|
| 1. Hold | Sterilizer out of service and labelled; loads since the last negative result quarantined | Which loads are in scope | Out-of-service tag with time, and a quarantine list by load identifier |
| 2. Verify the test | Inspect the indicator, run the control, confirm incubator temperature and incubation time, check lot and expiry | Is this a real positive, or a test-handling error | Biological indicator log entry with lot number, expiry, incubator, reader and control result |
| 3. Read the physical record | Printout or electronic record for time, temperature and pressure; cycle type selected | Did the cycle run as intended | Cycle record attached to the investigation, with the parameters transcribed |
| 4. Audit the load | Packaging type and size, loading pattern, pouch orientation, mass, mixed materials | Is the cause on the load side | Load description and photographs, with the corrective action named |
| 5. Challenge the machine | Repeat a biological indicator on the same cycle type; service provider if the repeat is positive; after repair, three consecutive biological indicators and three Bowie-Dick tests | Is the sterilizer fit for use | Service report plus requalification results, signed by the provider and by the person who released the sterilizer |
| 6. Look back and release | Work back to the last negative result, retrieve and reprocess unused items in another sterilizer, complete the look-back report, contact the College or public health for risk assessment | Who may have been exposed, and what they are told | Look-back report listing dates, load identifiers, chemical and biological results, instruments and patients, with the risk assessment attached |
Two features of that table matter more than the wording. First, step 2 exists because a positive result has more than one possible origin, and the Ontario cause list explicitly includes indicator storage and handling alongside packaging, loading and equipment faults. Second, step 5 is the only step that can be delegated entirely to a service provider, and it is the step that most often lacks a signature from the practice.
Who signs what
The documentation duty is not one document. It is six, and the division of labour is what makes the file defensible.
| Document | Who completes it | What it must contain | Where it lives and for how long |
|---|---|---|---|
| Daily sterilizer log | The person who runs the cycle | Physical parameters for each cycle — time, temperature, pressure — with the cycle identifier and initials | Office log, retained at least 10 years after the last entry |
| Biological indicator record | The person who runs and reads the test | Date, sterilizer, cycle type, indicator lot, expiry, control result, incubation conditions, result, reader | With the daily log; the self-audit form expects indicator plus control once daily per cycle type |
| Out-of-service and quarantine record | Infection control lead or office manager | Time the sterilizer was pulled, who authorized it, loads affected, where they were held | Investigation file |
| Service report | The equipment service provider | Fault found, parts replaced, tests performed after repair, technician signature and date | Investigation file, and the equipment maintenance log |
| Requalification record | Service provider plus the clinician who releases the sterilizer | Three consecutive biological indicator results, three Bowie-Dick results for dynamic air removal units, and the release decision | Investigation file, referenced in the daily log |
| Look-back report and recall policy | Practice owner or dentist | Loads, dates, patients, exposure, follow-up, and the written contingency plan that was followed | Policy manual; the self-audit form asks for a written recall policy and procedure |
The retention number deserves emphasis because it is the one an assessor can check without reading a single clinical note. The standard of practice requires the log book to be maintained for at least 10 years from the date of the last entry, and the same standard requires the daily operation of every sterilizer to be reviewed and documented. A practice that keeps the log for two years and the investigation report for ten has inverted the requirement.
The last row is where most files are thin. A recall policy that exists but has never been exercised reads as boilerplate. A recall policy with one completed look-back attached reads as a system that has been tested against a real event.
What does a positive biological indicator actually prove?
It proves that the spores in that indicator survived the cycle as delivered. It does not, by itself, prove that the sterilizer is broken, and it does not prove that the instruments in the load were contaminated. Those two statements are different, and the difference is what steps 2 to 4 are for.
| Observation | What it supports | What it does not support |
|---|---|---|
| Biological indicator positive, chemical indicator passed, physical parameters in range | A load-side or test-side cause deserves the first look: packaging, loading, indicator handling | A conclusion that the machine is at fault |
| Biological indicator positive, physical parameters out of range | A process failure with a record that shows it | A conclusion about which load was affected without the look-back |
| Biological indicator positive, repeat on the same cycle type negative, cause identified | A confined cause that was corrected | Release of the original load without reprocessing |
| Biological indicator positive, repeat positive after repair | A machine fault requiring requalification evidence | Return to service on the strength of the repair invoice alone |
| Control positive, test indicator negative | A test-system problem that invalidates the run | Any inference about the sterilizer |
The control vial in that last row is the reason the self-audit form pairs the two. A biological indicator without a control tells you a result; a biological indicator with a control tells you whether the result can be read at all.
How is the sterilizer returned to service?
Not by the repair alone, and not by a single passing retest. Ontario's flowchart and the provincial advisory both require a defined set of passing tests after a repair before the sterilizer goes back into routine use: three consecutive biological indicator results, and for dynamic air removal sterilizers, three consecutive Bowie-Dick tests. The advisory is explicit that a sterilizer is not approved for use if the biological indicator is positive on any of the required tests.
The requalification triggers are worth listing separately, because practices tend to treat only "broken" as a trigger. The events that reopen the question include major repair, construction or relocation affecting the area, a change to the steam or water supply, and a failed load that points to air removal. Each of those is a reason to re-run the sequence rather than to trust the previous result.
The biological indicators after a sterilizer repair article takes the requalification sequence apart test by test, including what changes for a Class B tabletop unit compared with a vacuum-assisted unit in a hospital department.
What does the daily requirement actually say?
In Ontario the answer is a daily test, not a weekly one, and the attribution matters because the two sentences circulate interchangeably.
| Statement | Where it comes from | How a policy should use it |
|---|---|---|
| A biological indicator plus a control test, once daily, for each type of cycle | RCDSO infection prevention and control self-audit form | The frequency a practice in Ontario has to state and be able to evidence |
| A biological indicator each day the sterilizer is used, and for each type of cycle used that day | Public Health Ontario provincial advisory, attributed to the CSA steam sterilization standard | The requirement language to quote in a policy or an audit response |
| At least weekly, preferably daily, plus every load with implants | ANSI/AAMI ST79, United States recommended practice | A comparison line only, labelled as a United States baseline |
| Every load containing implantable devices carries a biological indicator and is quarantined until the result is known | RCDSO standard of practice | The rule that governs implant loads regardless of the daily schedule |
The cross-jurisdiction error to avoid is writing the weekly sentence into a Canadian policy and describing it as meeting provincial expectations. It does not. The weekly sentence is a United States recommended-practice baseline; the Ontario documents say daily. The CSA Z314 and AAMI ST79 monitoring comparison sets the two documents side by side, and the daily testing requirement in dental practice treats the frequency question on its own.
A related trap sits in the classification. A passing Class 5 or Class 6 chemical indicator is not a substitute for the biological indicator; it is the item that may justify releasing a routine load while the biological result is pending, and only under the conditions the standard of practice sets out: a recording device, the specified chemical indicator class, and the physical parameters documented for that cycle. Implant loads do not get that option.
What does this change on the shelf?
Two consumable decisions determine whether the investigation can be run at all. The first is whether the indicators on the shelf match the cycle types the practice actually runs, because the daily test has to cover each type of cycle, not just the one used most often. The second is the incubation window, because the read time sets how long an implant load sits in quarantine.
A 24-hour readout indicator is the format most dental practices settle on: the 24-hour steam biological indicator carries a spore strip for Geobacillus stearothermophilus, and a dry block biological indicator incubator at 57 to 60 °C is what makes the read reproducible enough to defend. The packaging side matters too, because a sealed pouch that fails is a load-side cause that the investigation will surface: a Class 4 self-sealing pouch with a process indicator records exposure, while the biological indicator records lethality, and the two answer different questions.
The record side is where a practice can buy itself time. A log that captures sterilizer identity, cycle type, load identifier, indicator lot and result in a fixed field order is auditable in minutes; a notebook that captures the date and a tick is not. The compliance log centre runs the same field set in a browser without an account and prints as a blank sheet, and the wider frame — loading, packaging, release and records across the Canadian, United States and European documents — sits at the sterilization compliance hub.
Ordering for a clinic, a lab or a care home? Wholesale and multi-site ordering covers account setup and multi-site delivery, and the B2B wholesale collection lists the lines stocked for institutional buyers. Reselling? become a distributor.
Have a question about your own facility? Send it in and you will get a written answer specific to your setup, with the regulation or standard it is based on cited. Ask your compliance question.
Related reading
- Your biological indicator came back positive: the step-by-step walk-through — the same event narrated as a sequence of decisions.
- Biological indicators after a sterilizer repair: how many, and in what order — the requalification evidence a service report has to carry.
- CSA Z314 and AAMI ST79: where the monitoring requirements divide — the document-level split behind the daily-versus-weekly question.
Frequently Asked Questions
Does a positive biological indicator mean the sterilizer is broken?
No. It means the spores in that indicator survived the cycle as delivered, and the cause can sit on the load side, in test handling, or in the machine. Ontario's published cause list names operator error as the most common origin, with overloading, packaging density, loading pattern, pouch size and mixed materials all ahead of equipment failure. Treat the machine as suspect until the investigation rules it out, but do not skip the load-side and test-side steps on the way there.
Can a load be released while the biological result is pending?
For implants, no: a load containing implantable devices must carry a biological indicator and remain quarantined until the result is known. For routine loads, the Ontario standard of practice prefers holding the load until the result is available, and permits release only when a specified class of chemical indicator plus the cycle's documented physical parameters justify it — and only where the sterilizer configuration allows that route. The condition is a documented justification, not a default.
How many passing tests are needed before the sterilizer goes back into use after a repair?
Three consecutive biological indicator results, and for dynamic air removal sterilizers, three consecutive Bowie-Dick tests. The provincial advisory also states that a sterilizer is not approved for use if the biological indicator is positive on any of the required tests, which means a run of three that includes one positive restarts the sequence rather than averaging out.
What happens to instruments that were used after the last negative result?
The practice works back to the last negative biological indicator, retrieves any unused items from the affected loads and reprocesses them in a sterilizer that is not under investigation, and completes a look-back report covering the dates, load identifiers, chemical and biological results and the instruments involved. Risk assessment and patient follow-up sit inside that report, and the Ontario flowchart directs practices to contact the College or public health for assistance with the risk assessment rather than deciding exposure alone.
How long must the sterilization records be kept?
The standard of practice requires the log book to be kept for at least 10 years from the date of the last entry, and requires the daily operation of every sterilizer to be reviewed and documented in that log. The investigation file — quarantine record, service report, requalification results and look-back — should follow the same retention horizon, because an assessor who asks for the log will ask for the event that sits inside it.
Is a control test needed every day, or only when a result looks wrong?
Every day the test is run. The Ontario self-audit form pairs the two: a biological indicator plus a control test, once daily, for each type of cycle. The control is what establishes that the incubation conditions and the indicator lot can produce a readable result at all, so a positive test without a control leaves the practice unable to say whether the failure was in the load or in the test system.
Does a weekly spore test satisfy an Ontario practice?
No. Ontario's documents state a daily requirement — each day the sterilizer is used, and each type of cycle used that day. The weekly sentence, at least weekly and preferably daily, is the ANSI/AAMI ST79 recommended practice for the United States. Both statements are accurate in their own jurisdiction; a Canadian policy that adopts the weekly wording and describes it as meeting provincial expectations is a documentation defect, and it is one of the most common findings in this subject.
Every CliniEco Medical product is manufactured under an ISO 13485 quality management system and distributed under Health Canada MDEL #35334. If your question is which document governs a specific sterilizer, a specific record or a specific investigation in your clinic, our specialists will read the standard with you rather than paraphrase it.
Sources
- RCDSO, Standard of Practice: Infection Prevention and Control in the Dental Office
- RCDSO, IPAC Self-Audit Review Form (biological indicator and control, once daily per cycle type)
- RCDSO, Potential Causes of a Positive Biological Indicator
- RCDSO, Steps to Investigate a Positive Biological Indicator (flowchart)
- RCDSO, Infection Prevention and Control standards and advisories index
- Public Health Ontario, provincial infectious diseases advisory: cleaning, disinfection and sterilization in health care settings
- ISO 11138-1:2017, Sterilization of health care products — Biological indicators — Part 1: General requirements
- ISO 11138-3:2017, Biological indicators — Part 3: Indicators for moist heat sterilization processes
- ISO 14161:2009, Biological indicators — Guidance for the selection, use and interpretation of results
- ISO 17665:2024, Sterilization of health care products — Moist heat
- CAN/CSA-Z314:2023, Sterilization of medical devices (consolidated Canadian standard)
- ANSI/AAMI ST79:2017/(R)2022 with amendments, steam sterilization recommended practice
- Centers for Disease Control and Prevention, disinfection and sterilization in healthcare facilities
- Public Health Ontario, IPAC checklist for dental reprocessing
- Public Health Ontario, IPAC core checklist for dental settings