How Often Should You Run an Air Removal Test on a Pre-Vacuum Autoclave?

Run an air removal test on a pre-vacuum sterilizer at the start of each day the sterilizer is used, before the first load. The test, most often the Bowie-Dick type, confirms that the vacuum stage removed air from the chamber and that steam can penetrate a dense pack. If it fails, the unit should not be used for routine loads until the fault is corrected and the test passes.

Why Does a Pre-Vacuum Sterilizer Need a Daily Air Removal Test?

A pre-vacuum cycle removes air mechanically before steam enters. If air is trapped, steam cannot reach the load uniformly and the cycle may not sterilize, even if the gauges look correct. The air removal test is designed to reveal that failure directly, which is why it runs first, on an empty chamber, before any instruments are processed.

The test is not a substitute for biological monitoring. It checks the vacuum and steam penetration function of the machine; the biological indicator checks the kill. A clinic needs both, on their own schedules, and logs them separately so a reviewer can see that each control was performed.

When Should the Test Be Run and Logged?

Run it at the start of the working day, on a cold chamber, before the first load. Record the date, the cycle type, the result, and the operator. Some clinics also repeat the test after a major repair or a long shutdown, which is good practice even where it is not explicitly required, because both events can change vacuum performance.

CliniEco Medical Class 4 dual-indicator sterilization pouches, 200-pack, used for packaging and integrity control in a sterile processing suite

The record matters as much as the test. An air removal result that is not logged is, for audit purposes, a test that did not happen. A short line in the same log as the biological indicator results, with a pass or fail and an initial, keeps the whole day's sterility assurance in one place.

What Should You Do When an Air Removal Test Fails?

Stop using the sterilizer for routine loads. Re-run the test on a cool chamber to rule out a procedure error such as a hot chamber or an incorrectly prepared test pack. If it fails again, treat it as a machine fault: check the door gasket, the drain, the vacuum pump and the steam supply, and escalate to service.

Once the fault is repaired, run the test again and record the pass before returning the unit to service. Any load processed after a failed test should be considered suspect until it can be reprocessed, which is why the failed result belongs in the log immediately rather than at the end of the day.

Pair of blue nitrile examination gloves laid out flat for a care or housekeeping task
Question Answer
When to run Start of each working day, cold chamber, before first load
Chamber state Empty
What it checks Air removal and steam penetration
What it does not check Spore kill (that is the biological indicator)
On failure Stop routine use, retest, service, retest and record pass

Related reading

Sterilization compliance hub; daily air removal and Bowie-Dick requirements; autoclave chamber cleaning frequency.

Download the printable sterilization log sheet and use the autoclave log generator. Ask a Sterilization Compliance Specialist at the compliance desk. Ordering for a clinic, lab or care home? Wholesale and multi-site ordering and the B2B wholesale collection cover case pricing and account setup. Clinics can also 24-hour biological indicator 25-pack. Reselling? become a distributor.

Frequently Asked Questions

How often should an air removal test be run?

At the start of each day the pre-vacuum sterilizer is used, on a cold empty chamber before the first load, and again after any major repair or long shutdown.

Is an air removal test the same as a biological indicator test?

No. The air removal test checks that air was removed and steam can penetrate; the biological indicator checks that spores were killed. A clinic needs both.

What do you do if the air removal test fails?

Stop using the sterilizer for routine loads, retest on a cool chamber, and if it fails again treat it as a machine fault, service it, then retest and record a pass before returning to service.

CliniEco Medical is a licensed medical device establishment (MDEL #35334).

Vous travaillez déjà avec des cliniques ? Devenez représentant régional.