A Vancouver food-testing laboratory ran its sterilization monitoring across three shifts, and each shift kept its own version of the log. The biological indicator results were all present, but the three formats did not share a single field in common, so a failure on the night shift could not be compared with the same sterilizer's behaviour on days without rewriting the week by hand.
Nothing in the monitoring programme was wrong. The records were the problem, and the fix was a single log template plus one column that had been missing from all three versions.
What did the three log formats look like?
The day shift used a printed sheet with the cycle parameters written in a grid. The afternoon shift logged results in a notebook and transcribed them weekly. The night shift recorded the indicator result and the operator on a whiteboard that was photographed at the end of the shift. Each format captured the result; none captured the incubation start time consistently, and none used the same sterilizer identifier wording.
The consequence was that a trend across shifts was invisible. A single failure was investigated at the time, but a slow drift in read times, which is exactly what a shift-based operation should watch for, could not be seen on paper.
Why were the records hard to compare?
Three reasons. The sterilizer identifier was written three different ways, so the same machine looked like three machines. The incubation start was recorded on two of three formats, so the interval could not be verified. And the entry order differed, so the sequence of a shift's activity could not be reconstructed without interpretation.
Transcription also introduced a delay. The afternoon shift's notebook was typed up weekly, which meant that a problem noticed on Wednesday was confirmed on the following Monday.
What did the lab change?
It replaced all three formats with one printed template used by every shift, and added the incubation start time as a required field. The sterilizer identifier was standardised to the equipment asset number, and the physical monitoring parameters were reduced to the three fields that the lab actually used for trend analysis rather than the full grid.
Crucially, it kept the template paper-based. A laboratory that considered a spreadsheet decided against it because the night shift works through the same bench area and had no convenient terminal at the sterilizer, and an electronic record that nobody fills in is worse than a paper one that everyone does.
| Before | After |
|---|---|
| Three formats, three shifts | One template, all shifts |
| Sterilizer ID written three ways | Equipment asset number only |
| Incubation start on two of three formats | Incubation start required on all |
| Weekly transcription delay | Weekly review of the same sheet |
| Full parameter grid | Three parameters used for trend analysis |
How was the change verified?
The lab ran the unified template for six weeks, then compared the review process with the old one on three measures: the time to confirm an out-of-range read, the number of records with a missing incubation start, and the number of investigations that crossed shifts. Time to confirm fell from days to the same shift, missing incubation starts fell to zero, and the first cross-shift trend appeared in week four, which the lab had not been able to see before.
That trend was a gradual lengthening of read times on the night shift's second machine, traced to an incubator temperature that had drifted because it was stored next to a heat source. Nothing was failing yet, and the point of the exercise was to see it before it did.
What should another lab take from this?
A monitoring programme is only as good as the records that make its trends visible. Where several shifts or several benches share sterilizers, the fields that matter most are the machine identifier and the incubation start, because those are what let one shift's data be compared with another's. Unifying the template costs a print run and produces a measurement capability that separate formats do not.
What should a lab do next?
Print the daily sterilization log sheet and standardise the sterilizer identifier to the asset number, then run the sterilization self-check to confirm the incubation start is captured on every shift. The sterilization compliance hub links the related monitoring guides.
The sterilization monitoring collection lists indicators and incubators together, including 24-hour rapid-readout biological indicators and a DLAB HB105-S1 dry bath incubator. Ordering for a multi-shift lab or a network of sites? Wholesale and multi-site ordering covers case pricing and account setup, and the B2B wholesale collection lists the institutional lines. Testing a unified record routine on a small scale first? Start with the 24-hour biological indicator 25-pack. If you want your multi-shift monitoring records reviewed for trend visibility, ask a compliance specialist. Reselling? become a distributor.
Related reading
- Autoclave Spore Test Log Fields
- Case Review: A Canadian Lab's Spore Test Failure Investigation
- Case Review: Cutting Spore Test Turnaround in a Food Plant Lab
Frequently Asked Questions
Why does the incubation start time matter on a spore test log?
Because the interval between the cycle and the read is what determines whether the result is valid. Without the incubation start, a shortened interval cannot be detected, and a shortened interval is one of the most common causes of a false failure reading.
Should sterilization records be electronic?
Only where the system is actually used at the point of monitoring. A paper template that every shift fills in produces better data than a system with no terminal near the sterilizer. The record has to fit the workflow to be reliable.
Why standardise the sterilizer identifier?
So that the same machine is the same machine in every record. Where an identifier is written differently on different shifts, one sterilizer can look like several, and a trend on that machine cannot be seen without manual reconciliation.
What is the benefit of reviewing records weekly?
It turns a log into a measurement. A weekly review surfaces slow drift, such as lengthening read times or a machine drifting out of normal behaviour, while the cause is still cheap to correct rather than after a failure.
CliniEco Medical is a licensed medical device establishment (MDEL #35334).