Which Standards Apply to a Catheter Accessories Kit in Ontario Clinics?

Illustration of a catheter accessories kit showing a urinary drainage bag, its tubing and the connector that joins them

Four layers of rules reach a catheter accessories kit in an Ontario clinic. The federal Medical Devices Regulations decide what the kit is and who may sell it. The ISO documents decide what the catheter, the drainage bag and the connectors have to be. The licence provisions decide what the supplier must hold. Ontario's workplace and clinical rules decide how the staff who handle the kit are expected to act.

A clinic orders the kit as one line, and the line usually means the catheter accessories kit with a urinary drainage bag and tubing, supplied matched so a change does not stop for a missing connector. Where the same round stocks pads and skin care as well, the urology care kit carries the incontinence pads, skin barrier wipes and disposal bags separately rather than inside the catheter kit.

What is in a catheter accessories kit, and which standard covers each part?

Each component answers to a different document, which is why a supplier who cites one standard number for the whole kit has usually described the catheter and left the rest undefined.

Component Document that governs it What the document fixes
Urethral catheter ISO 20696:2018, sterile urethral catheters for single use Dimensions, tip and balloon performance, sterility and catheter labelling
Drainage bag and tubing ISO 20697:2018, sterile drainage catheters and accessory devices The bag, the tubing and the accessory devices supplied as a set
Small-bore connectors ISO 80369-7:2021 Connector dimensions and performance so parts from different suppliers mate
Sterile barrier packaging ISO 11607-1:2019 The packaging system that keeps the kit sterile until it is opened
Patient-contact materials ISO 10993-1:2018 The biological evaluation framework for the materials used
Label and instructions Medical Devices Regulations, sections 21 and 23 What the label states, and in which language

The two ISO documents are not interchangeable. ISO 20696:2018 covers sterile urethral catheters for single use; ISO 20697:2018 covers sterile drainage catheters and accessory devices. A specification citing only 20696 has described the catheter and said nothing about the bag that hangs on the bed.

Connectors are the quiet failure. ISO 80369-7:2021 specifies small-bore connector dimensions and performance; for a kit the practical consequence is that a bag whose connector does not match the stock in the cupboard gets set aside mid-round.

Illustration of a catheter accessories kit showing a urinary drainage bag, its tubing and the connector that joins them
One kit, three governed parts: the catheter answers to ISO 20696:2018, the bag and tubing to ISO 20697:2018, the connector to ISO 80369-7:2021.

Which federal rules decide whether a kit can be supplied in Ontario?

Two separate questions sit here, and clinics often merge them: what the device is, and who may import or sell it.

A urinary catheter penetrates the body through a body orifice, and Rule 2(1) of Schedule 1 to the Medical Devices Regulations classifies invasive devices that do so as Class II. Rule 2(3) moves a device normally intended to remain in the body for at least 30 consecutive days to Class III, which is why the intended indwell, not the shelf life, decides the licence obligation.

Section 26 makes the licence operative: no person shall import or sell a Class II, III or IV device unless the manufacturer holds a licence for it. Section 44(1) adds an establishment licence for the importer or seller, and subsection 44(2) exempts, among others, retailers and health care facilities. A clinic buying through a distributor therefore sits outside that duty; a clinic importing directly does not.

Section 21(1) fixes what the label carries, including the expiry date where the device has one, set by the component with the shortest projected useful life, plus any special storage conditions. On a kit the shortest-lived component is usually the sterile barrier of the bag rather than the tubing.

Disposable underpads laid out in six sizes above a hospital-style bed made up with a pad
A catheter round is a scheduled event on a made-up bed: the kit is one line among several the same visit consumes, and bedding protection is counted separately.

Which Ontario rules sit above the federal ones?

Ontario does not licence catheter kits. It licences the places and regulates the work, and that is where an Ontario file gains sections a federal file does not have.

The employer duty is the broadest. Section 25(2)(h) of the Occupational Health and Safety Act requires an employer to take every precaution reasonable in the circumstances for the protection of a worker, and emptying and handling a drainage bag is exactly the task that duty is written for. Public Health Ontario's routine practices turn that duty into a routine: gloves where contact with body fluid is anticipated, hand hygiene between clients, and a glove change between people rather than between tasks.

Long-term care adds a procurement obligation. O. Reg. 246/22, section 56, requires an annual evaluation of residents' satisfaction with the range of continence care products and makes it count when purchasing decisions are made, which turns the choice of bag into part of a documented review.

If the clinic collects urine specimens for culture rather than testing on site, a third instrument arrives. A place where specimens are taken or collected is a specimen collection centre under the Laboratory and Specimen Collection Centre Licensing Act, and section 9(3) prohibits operating one without a licence from the Director. R.R.O. 1990, Reg. 682, section 14, then designates the Institute for Quality Management in Healthcare to carry out the quality management programme an inspector will ask a licensed site to show.

None of that changes the kit. All of it changes the file that travels with it.

How does an Ontario clinic's kit file differ from the one kept in the United States and elsewhere in Canada?

The kit is the same object; the paper around it is not. Canada asks for a manufacturer licence and, for the seller, an establishment licence, while the United States asks the manufacturer for a premarket submission and both parties for registration and listing.

Item Canada (Ontario clinic) United States
Rule that sets the class Schedule 1 of the Medical Devices Regulations; body-orifice invasive falls to Rule 2(1) Device-type regulation in Title 21
What the supplier needs Manufacturer licence under section 26, plus establishment licence under 44(1) unless exempted by 44(2) Premarket clearance for the device type, plus registration and listing
How a Foley kit is recorded Class II by rule, licence number on the file rather than on the pack Product code PPB, assigned to 21 CFR 876.5130, listed as Class II in the FDA classification database
Urine drainage bag Non-invasive device storing body fluid; the file should show which rule the manufacturer applied Product code NNZ or EYZ, assigned to 21 CFR 876.5250, listed as Class I
What an inspection looks at Provincial guidance plus the employer duty, evidenced by the clinic's written procedure Facility survey against 42 CFR 483.25(e)

The American side carries one packaging trap. Section 876.5250 covers urine collectors and accessories, so a file citing it for the catheter as well as the bag has used the right section for the wrong component; the catheter has its own product code.

Is the drainage bag held to the same standard as the catheter?

No, and that is why a kit needs two ISO documents rather than one. The catheter is invasive and enters under Rule 2(1). The bag and tubing are non-invasive: they store a body fluid rather than introduce it, so the classification file should show whether the manufacturer classified under Rule 5, which covers non-invasive devices for channelling or storing liquids and body fluids for introduction into the body, or under Rule 7(1), the residual rule for other non-invasive devices.

The performance documents separate in the same way. ISO 11607-1:2019 governs the packaging system that keeps the kit sterile, and ISO 10993-1:2018 is the framework for evaluating the materials that touch the patient. A bag sterile inside a pack whose seal failed is not a sterile bag, which is why the packaging document belongs in the same file as the product document.

What language does the label have to be in, Ontario compared with Canada and the United States?

Federal law sets a floor, and the floor is lower than most buyers assume. Section 23(1) of the Medical Devices Regulations says the information required by section 21(1) shall, as a minimum, be in either English or French; only where the device is sold to the general public does section 23(3) require both. A kit sold into professional channels in Ontario can therefore carry one language and still meet the federal minimum, and Ontario adds nothing to that for a professional-use device.

Quebec does add something, which matters to a clinic that operates on both sides. Section 51 of the Charter of the French language requires every inscription on a product, its container, its wrapping and the documents supplied with it, including directions for use, to be drafted in French, with a translation permitted alongside.

In the United States the language rule arrives with 21 CFR part 801 and requires English. A Canadian professional pack may lawfully be unilingual, a Quebec pack may not, and an American pack is English by default.

What should an Ontario buyer ask for before the first order?

Five documents, each closing a specific gap. Ask for the manufacturer's licence number and the device identifier it covers, because section 26 makes the licence the condition of lawful sale. Ask for the supplier's establishment licence or its exemption basis under 44(2). Ask for declarations of conformity to ISO 20696:2018 and ISO 20697:2018 with edition years, because undated certificates cannot be checked. Ask for the packaging validation summary against ISO 11607-1:2019. Ask for instructions for use in the language your staff read.

The material question sits behind those five. ISO 10993-1:2018 is a framework rather than a pass mark, so the useful question is which biological endpoints were evaluated for the parts contacting mucosa, not whether a certificate exists.

How does a clinic keep the kit file ready for an inspection?

One folder per supplier, following the product rather than the purchase order: licence, ISO declarations with edition years, packaging validation, instructions for use — that is the order an inspector asks for them.

The handling record is a second folder, and it is where Ontario differs from a federal-only file. Section 25(2)(h) is an outcome duty, so the evidence is a written procedure plus a record that staff followed it: gloves and hand hygiene per Public Health Ontario, a bag change interval taken from the manufacturer's instructions for use, and a note of who changed what and when. The WHO infection prevention programme pages frame that procedure, the Canadian Centre for Occupational Health and Safety covers the biological hazard side of the same task, and the CDC standard precautions guidance shows how the same routine is written where the file crosses the border.

For a clinic that also collects specimens, the College of Nurses of Ontario standards sit beside the collection centre licence: the licence governs the place, the practice standard governs the person.

References

  • Medical Devices Regulations, SOR/98-282, Schedule 1 Rules 2 and 7, sections 21, 23, 26, 44 — laws-lois.justice.gc.ca (checked 11 November 2026)
  • Medical devices portal — canada.ca (checked 11 November 2026)
  • ISO 20696:2018, sterile urethral catheters — genorma.com (checked 11 November 2026)
  • ISO 20697:2018, sterile drainage catheters and accessory devices — genorma.com (checked 11 November 2026)
  • ISO 80369-7:2021, small-bore connectors — genorma.com (checked 11 November 2026)
  • ISO 11607-1:2019, packaging for terminally sterilized devices — genorma.com (checked 11 November 2026)
  • ISO 10993-1:2018, biological evaluation — genorma.com (checked 11 November 2026)
  • FDA classification record, product code PPB, 21 CFR 876.5130 — open.fda.gov (queried 11 November 2026)
  • 21 CFR 876.5250, urine collector and accessories — law.cornell.edu (checked 11 November 2026)
  • 42 CFR 483.25(e), quality of care — law.cornell.edu (checked 11 November 2026)
  • 21 CFR part 801, labelling — ecfr.gov (checked 11 November 2026)
  • Occupational Health and Safety Act, s. 25(2)(h) — ontario.ca (checked 11 November 2026)
  • O. Reg. 246/22, s. 56, continence care — ontario.ca (checked 11 November 2026)
  • Laboratory and Specimen Collection Centre Licensing Act, s. 9(3) — ontario.ca (checked 11 November 2026)
  • R.R.O. 1990, Reg. 682, Laboratories, s. 14 — ontario.ca (checked 11 November 2026)
  • Routine practices and additional precautions — publichealthontario.ca (checked 11 November 2026)
  • Charter of the French language, C-11, s. 51 — legisquebec.gouv.qc.ca (checked 11 November 2026)
  • Institute for Quality Management in Healthcare — iqmh.org (checked 11 November 2026)
  • College of Nurses of Ontario, standards — cno.org (checked 11 November 2026)
  • Biological hazards — ccohs.ca (checked 11 November 2026)
  • Infection prevention and control — who.int (checked 11 November 2026)
  • Standard precautions for healthcare — cdc.gov (checked 11 November 2026)

Related reading

Frequently asked questions

Which standards apply to a catheter accessories kit in Ontario clinics?

Four layers. The federal Medical Devices Regulations set the class, the licence and the label. ISO 20696:2018 covers the urethral catheter, ISO 20697:2018 the drainage bag and tubing, ISO 80369-7:2021 the connectors, ISO 11607-1:2019 the sterile packaging. Ontario adds the employer duty in section 25(2)(h) of the Occupational Health and Safety Act and Public Health Ontario's routine practices.

Does a catheter accessories kit need a device licence in Canada?

For the device type, yes. Section 26 prohibits importing or selling a Class II, III or IV device unless the manufacturer holds a licence, and a catheter passing through a body orifice falls to Rule 2(1), which is Class II. Rule 2(3) moves a device intended to remain in the body 30 days or more to Class III. Section 44(1) adds an establishment licence, with exemptions in 44(2).

Is the drainage bag regulated in the same way as the catheter?

No. The catheter is invasive and enters under Rule 2(1). The bag and tubing are non-invasive devices that store body fluid, so the file should show whether the manufacturer applied Rule 5 or Rule 7(1). The performance documents differ too: ISO 20696:2018 for the catheter, ISO 20697:2018 for the bag and tubing.

Does the label have to be in both English and French in Ontario?

Not for a professional-use device. Section 23(1) requires the section 21(1) information to be in either English or French at minimum, and only devices sold to the general public need both under section 23(3). Quebec differs: section 51 of the Charter of the French language requires the inscriptions to be in French, with a translation permitted alongside.

What documents should an Ontario buyer ask for before ordering?

The manufacturer licence number with the identifier it covers, the supplier's establishment licence or exemption basis, ISO 20696:2018 and ISO 20697:2018 declarations with edition years, the packaging validation summary against ISO 11607-1:2019, and instructions for use in the language staff read.

How does the Ontario file differ from an American one?

Canada asks the manufacturer for a licence and the seller for an establishment licence; the United States asks the manufacturer for a premarket submission and both parties for registration and listing. The Foley kit carries product code PPB, assigned to 21 CFR 876.5130 and listed as Class II, while a urine drainage bag is assigned to 21 CFR 876.5250 and listed as Class I.

Keeping the kit file in one place

The compliance log centre holds the printable logs that keep a change record and a stock count in one document, and the supply planner on the same page turns a change interval into a monthly kit count. For a standing order across several Ontario sites, the route is the institutional account enquiry page; where catheter waste handling sits inside the same procedure as a clinic's reprocessing records, the sterilization compliance consultation covers that side. Reselling? become a distributor.

CliniEco Medical distributes clinic consumables in Canada under MDEL #35334. This article describes requirements published by Health Canada, the Government of Ontario and the United States federal register; the requirement that binds a specific clinic remains the one in its provincial guidance, its accreditation conditions and its own written procedure.

Last updated: 11 November 2026.

Already working with clinics? Become a regional representative.